manualshive.com logo in svg

Siemens Sirius 3RA6, Системное руководство


Поделиться
Скачать
background image

Accessories 

 

7.12 AS-i mounting module for 3RA61/3RA62 compact starter 

 

SIRIUS 3RA6 compact starter 

212

 

System Manual, 09/2014, NEB560060102000/RS-AA/006 

7.12.4

 

Installing/removal 

7.12.4.1

 

Installing the AS-i mounting module 

Requirements 

 

 

NOTICE 
Damage to the AS-i mounting module! 
If you install the AS-i mounting module on a compact starter that has a control supply 

voltage of more than 24 V, the AS-i mounting module will be supplied with too much power. 

This will damage the AS-i mounting module. 
Only install the AS-i mounting module on a compact starter with a control supply voltage of 

24 V. 

 

 

Note 
Damage to the AS-i mounting module! 
This will damage the AS-i mounting module if it is electrostatically charged. 
Please observe the ESD regulations when working with the AS-i mounting module. 

 

●

 

The control circuit terminals must be removed from the compact starter (24 V) (for 

information on removing the control circuit terminals, please refer to "Installing/removal 

(Page 144)"). 

●

 

The compact starter must be switched off (actuator set to   OFF position). 

Procedure 

 

Step 

Instructions 

Image 

1 

Insert the AS-i mounting module into the 

mechanically coded guiderail on the 

device from the bottom and then push it 

back until you hear it engage. 

 

Содержание Sirius 3RA6

































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sirius 3RA6

Mamas & Papas luna Manual preview
luna
Бренд: Mamas & Papas Страницы: 44
Mamas & Papas flare Manual preview
flare
Бренд: Mamas & Papas Страницы: 8
Omegalink 553 Quick Start Operation Manual preview
553
Бренд: Omegalink Страницы: 2
MamaLove rider Quick Start Manual preview
rider
Бренд: MamaLove Страницы: 9
Parker CK5-DN Quick Start Manual preview
CK5-DN
Бренд: Parker Страницы: 4
SYR 315.2 Instructions For Use preview
315.2
Бренд: SYR Страницы: 2
Reliance Foundry R-7651-EM Installation preview
R-7651-EM
Бренд: Reliance Foundry Страницы: 3
Wesa AE04 Installation And Operation Manual preview
AE04
Бренд: Wesa Страницы: 8
LMI Technologies Liquitron DP5000-01A Instruction Manual preview
Liquitron DP5000-01A
Бренд: LMI Technologies Страницы: 28
Motrona CA306 Operating Manual preview
CA306
Бренд: Motrona Страницы: 10
Pilz PSS67 IO1 16FDI Operating Manual preview
PSS67 IO1 16FDI
Бренд: Pilz Страницы: 36
DAQ SCXI-1102 User Manual preview
SCXI-1102
Бренд: DAQ Страницы: 63
Acumen Model L Operating Instructions Manual preview
Model L
Бренд: Acumen Страницы: 6
PCB Piezotronics 482B06 Installation And Operating Manual preview
482B06
Бренд: PCB Piezotronics Страницы: 12
Skov DOL 535 Technical Manual preview
DOL 535
Бренд: Skov Страницы: 68
Barco EC-210 Quick Start Manual-Setup preview
EC-210
Бренд: Barco Страницы: 4
Blue Point Engineering DMX Analyzer Manual preview
DMX Analyzer
Бренд: Blue Point Engineering Страницы: 12
Grundfos EC 15 Installation And Operating Instructions Manual preview
EC 15
Бренд: Grundfos Страницы: 80

Бренды по названию

Популярные бренды

Загрузить еще бренды