Siemens SION 3AE6113-0 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 60

background image

Transport, storage and packing

9229 0020 176 0B

7

2019-04-02

Opening the transport unit

• Place the transport unit on a level, non-slip and pressure-resistant surface.
• Remove lifting gear or transport means.
• Remove plastic wrap.
• Lever out fasteners from the carton and lift off carton (see Fig. 2).
• Remove film from the vacuum circuit-breaker.
• In the case of overseas packaging, push the lower film onto the pallet floor.
• Check that the delivery is complete.
• Check vacuum circuit-breaker for damage.

Fig. 2

Removing the fixings from the carton

Note

Do not use the vacuum circuit-breaker in case of damage such as breaks, cracks,
flaking, bent metal parts, damaged plug-in contacts, tears or bare cables.
Send it back in its original transport unit (see “Reuse of transport unit”, page 9).

«
...
5
6
7
8
9
...
»

Содержание SION 3AE6113-0





























































Отзывы:

Нет отзывов

Похожие инструкции для SION 3AE6113-0

Бренд: Westinghouse Страницы: 12

Бренд: Siemens-Allis Страницы: 38

Бренд: Eaton Страницы: 2

Panel/Link TC Series

Бренд: Reliance Controls Страницы: 2

Бренд: Telect Страницы: 12

Бренд: Eaton Страницы: 52

Бренд: DINWAY Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды