manualshive.com logo in svg

Siemens SIMOGEAR BA 203-A, Монтаж и эксплуатация

Поделиться
Скачать
Siemens SIMOGEAR BA 203-A Скачать руководство пользователя страница 33

Mounting of smooth shafts
The KS adapter has been designed for mounting servomotors with smooth shafts (without 
feather key).

Permissible
SIMOTICS S-1FL6

1FL6XXX‑XXXXX‑XXGX
1FL6XXX‑XXXXX‑XXHX

SIMOTICS S‑1FK2

1FK2XXX‑XXXXX‑0XXX

SIMOTICS S-1FK7

1FK7XXX‑XXXXX‑XXGX
1FK7XXX‑XXXXX‑XXHX

SIMOTICS S-1FT7

1FT7XXX‑XXXXX‑XXGX
1FT7XXX‑XXXXX‑XXHX
1FT7XXX‑XXXXX‑XXKX
1FT7XXX‑XXXXX‑XXLX

SIMOTICS M‑1PH8

1PH8XXX‑XXXXX‑0XXX

SIMOTICS S‑1FT7 Flange-mounted design
Only the classic flange may be used in this version. The recessed version cannot be mounted on 
the KS adapter.

Permissible
SIMOTICS S-1FT7

1FT7XXX‑XXXX1‑XXXX
1FT7XXX‑XXXX4‑XXXX

SIMOTICS S‑1FK2 IP65
The IP65 version of SIMOTICS S‑1FK2 is mechanically not compatible with the KS adapter. 
However, the degree of protection IP65 is nevertheless complied with by attaching the motor to 
the gear.

Permissible
SIMOTICS S‑1FK2

1FK2XXX‑XXXX0‑XXXX (IP64 without shaft sealing ring)

Not permissible
SIMOTICS S‑1FK2

1FK2XXX‑XXXX1‑XXXX (IP65 with shaft sealing ring)

Installing

4.5 Mounting the motor

SIMOGEAR adapters for gearboxes - KS, K2, K3, K4, K5, KQ, KQS, K8, A, AZ
Operating Instructions, 05/2022, A5E37431501A/RS-AL

31

Содержание SIMOGEAR BA 203-A































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды