Siemens SIMOGEAR BA 203-A Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 62

background image

Table 2-1

Article number code

SIMOGEAR adapter

Article number position
12

Supplement

Adapter KS for mounting a SIEMENS servomotor

1

-

Adapter K2 for fitting an IEC motor

2

-

Adapter K3 for fitting an NEMA motor

3

-

Short adapter K4 for fitting an IEC motor

4

-

Short adapter K5 for fitting an NEMA motor

5

-

Adapter KQ, KQS for fitting a servomotor

7

-

Adapter K8 for fitting a servomotor

8

-

Adapter A

9

M1A

Adapter AZ

9

M1B

Example of an article number code for a SIMOGEAR gearbox with coupling adapter KS
2KJ3xxx-xxA01-xxxx

Note

For a special design of the gearbox and the supplementary equipment, the contractual
agreements and technical documentation apply in addition to these operating instructions.

When using additional components, carefully observe the notes in the associated
documentation.

Refer to the other operating instructions and safety instructions supplied with the product.

Valid operating instructions for SIMOGEAR
can be found in SIOS (

https://support.industry.siemens.com/cs/de/en/ps/13424/man

)

• BA 2030 - operating instructions for SIMOGEAR gearboxes

• BA 2031 - operating instructions for permissible mounting position deviations of SIMOGEAR

gearboxes

• KA 2032 - compact operating instructions for SIMOGEAR worm geared motor S

• BA 2039 - operating instructions for adapters for mounting on SIMOGEAR gearboxes

• BA 2330 - operating instructions for LA/LE/LES motors for mounting on SIMOGEAR gearboxes

• BA 2331 - operating instructions for geared motors with DRIVE-CLiQ safety-related encoder

for safety-related applications

• BA 2332 - operating instructions for geared motor with holding brake for safety-related

applications

• BA 2535 - operating instructions for SIMOGEAR electric monorail gearboxes

• BA 2730 - operating instructions for SIMOGEAR geared motors with rotary encoder for safety-

related applications

The described gearboxes correspond to the state-of-the-art at the time these operating
instructions were printed.

Siemens reserves the right to change individual components and accessory parts in the interest
of ongoing development. The changes are designed to improve performance and safety. The

Specific safety instructions
2.1 General overview

SIMOGEAR adapters for gearboxes - KS, K2, K3, K4, K5, KQ, KQS, K8, A, AZ

20

Operating Instructions, 05/2022, A5E37431501A/RS-AL

«
...
20
21
22
23
24
...
»

Содержание SIMOGEAR BA 203-A































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOGEAR BA 203-A

G120 - DNS NAS Server

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 2

SmartSwitch 6C110

Бренд: Cabletron Systems Страницы: 7

Бренд: cable matters Страницы: 52

Бренд: quadient Страницы: 2

Vive TC NE30W-EU

Бренд: HTC Страницы: 36

Бренд: HQ Страницы: 20

Бренд: Mesa Страницы: 2

Бренд: Proyecson Страницы: 148

Бренд: Allied Telesis Страницы: 2

Бренд: Federal Signal Corporation Страницы: 2

AirStation WLI-USB-KB11

Бренд: Buffalo Страницы: 45

Бренд: Emulex Страницы: 19

Бренд: Chamberlain Страницы: 1

Бренд: Lenze Страницы: 8

dx-uc202 - USB 2.0 PCMCIA Notebook Card

Бренд: Dynex Страницы: 16

Бренд: Salto Страницы: 2

CompactFlash CA1040

Бренд: Abocom Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды