Siemens SIMOCODE 3UF Скачать руководство пользователя страница 64

Страница: 64 / 172

Monitoring Functions

9.7 Operating Hours Monitoring

SIMOCODE PRO V PN FDI

Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

Response

Here you can determine the response for when the Permissible Motor Stop Time is

exceeded:

Response

Level

Disabled

Signaling

Warning

Tripping

9.7.4

Motor Start Limitation

Motor Start Limitation can protect system parts (motor, switching devices such as soft

starters, and converters) from too many start processes within a parameterizable time frame

and, thus, prevent damage. This is particularly useful for commissioning or manual control.

Schematic
The following schematic illustrates the principle of Motor Start Limitation:

Permissible Starts (CiR)
The maximum Number of Starts is set here. The time interval "Time Range for starts"

commences to run after the first start. After the second to last permissible start has been

executed, the "Just One Start Possible" prewarning is generated.

Permissible Starts: 1 - 255

Time Range for Starts (CiR)

The time range for permissible start processes is set here. The maximum number of starts is

only available again after the parameterized time range for starts has expired. The number of

available starts is shown by the analog value "Permissible Starts - Actual Value".
Time Range for Starts: 00:00:00 - 18:12:15 hh:mm:ss

Содержание SIMOCODE 3UF













































































































































































Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды

Siemens SIMOCODE 3UF, Руководство по программированию и эксплуатации

Результаты поиска

Содержание SIMOCODE 3UF

Отзывы:

Похожие инструкции для SIMOCODE 3UF

Бренды по названию

Популярные бренды