Siemens SIMATIC RTU3041C Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 95

background image

2 Engineering

Securely Connecting RTU3041C to TeleControl Server Basic
Entry ID: 109739240, V3.0, 07/2021

13

©

S

iem

e

n

s A

G

2021

A

ll r

igh

ts

re

se

rv

e

d

2.2

Configuration and Project Planning

This section describes the most important steps of the configuration:

•

Configuring the SINEMA Remote Connect Server (

•

Configure the SIMATIC RTU3041C (

) or load the supplied

configuration file (

•

Configuring the TeleControl Server Basic (

•

Configure OPC UA Clients (UaExpert) (

.

Note

To check the time validity of certificates, it is important that the current date and
time is kept on all devices.

Check the time specification on all devices and adjust if necessary. Alternatively,
you can have the system time automatically synchronized with an NTP Time
Server. This ensures that the current time is obtained precisely.

2.2.1

Configuring a SINEMA Remote Connect Server

This section shows you all necessary steps to configure a SINEMA Remote
Connect Server for the application described here.

In order to put the application example into operation, the SINEMA Remote
Connect Server must be installed and the web server must be accessible via the
LAN interface.

The process for installing the SINEMA Remote Connect Server can be found in its
instruction manual:

https://support.industry.siemens.com/cs/ww/en/view/109482121

Note

The router through which the SINEMA Remote Connect Server is connected to
the internet must have a fixed public IP address or a DNS name.

Note

To enable a secure VPN connection, you must set up port sharing on the VPN
client side and port forwarding on the VPN server side for each of the routers. The
following FAQ shows you which ports (port 1194 by default) are necessary for
this:

https://support.industry.siemens.com/cs/ww/en/view/109745584

«
...
11
12
13
14
15
...
»

Содержание SIMATIC RTU3041C
































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC RTU3041C

Бренд: Qingdao H.Y Страницы: 6

Бренд: ABB Страницы: 27

Бренд: Panasonic Страницы: 9

Бренд: Rain-Flo Irrigation Страницы: 20

Attest Auto-reader 390

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Бренд: 3M Страницы: 2

Dynapro ET 355 Monitor HL

Бренд: 3M Страницы: 23

PELTOR WS LiteCom Plus

Бренд: 3M Страницы: 7

Steri-Vac GS Series

Бренд: 3M Страницы: 52

Бренд: A.MENARINI Страницы: 2

Бренд: Above All Страницы: 4

VLR100 LED Series

Бренд: WE-EF Страницы: 3

Team Agile Color Tune TM16-0

Бренд: GRAU Страницы: 24

Бренд: Hoist Fitness Страницы: 17

Бренд: Peak Pilates Страницы: 4

Бренд: Meyer Страницы: 100

Rovelight RT-400

Бренд: Orlit Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды