manualshive.com logo in svg

Siemens Simatic PG 740 PIII, Руководство по эксплуатации

Поделиться
Скачать
Siemens Simatic PG 740 PIII Скачать руководство пользователя страница 22

Starting up and Operating the PG

2-6

Operating Instructions PG 740 PIII

A5E00063150-03

Switching off the PG 740 PIII

It is strongly recommended to close all applications and safely turn off the
operating system before switching off the PG 740 PIII. The procedure is described
in the “Getting Started Microsoft Windows 98” manual.

!

Warning

Do not switch off the PG 740 PIII while being connected to a network, errors in
data transfer and loss of data may occur. It could also damage the swap file on
your hard disk and cause loss of data.

Safely turn off the operating system in order to close the swap file and disconnect
from the network before switching off your PG.

To switch off the PG proceed as follows:

1. Close all applications and shut down the operating system.

2. Wait while the operating system prepares your PG to be turned off then switch

off the PG.

3. Depending on the operating system you have installed, the PG switches off

automatically or you have to switch it off via the On/Off switch. Now it is
possible to connect peripherals to the PG 740 PIII.

Содержание Simatic PG 740 PIII







































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды