Siemens SIMATIC NET RUGGEDCOM RST2228 Скачать руководство пользователя страница 34

Страница: 34 / 58

Device Management

This section describes how to connect to and manage the device.

3.1

Connecting to the Device

The following describes the various methods for accessing the RUGGEDCOM

RST2228P console and Web interfaces on the device. For more detailed instruc-

tions, refer to the

RUGGEDCOM ROS Configuration Manual

for the RUGGEDCOM

RST2228P.

USB Console Port

Connect a workstation directly to the USB Type-B console port to access the boot-

time control and RUGGEDCOM RST2228P interfaces. The console port provides ac-

cess to RUGGEDCOM RST2228P's console and Web interfaces.

NOTICE

Console ports are intended to be used only as a temporary connection during initial

configuration or troubleshooting.

Note

For Microsoft Windows users, the RUGGEDCOM USB Serial Console driver must be in-

stalled on the users workstation before connecting via the USB Type-B console port.

For more information, refer to the

RUGGEDCOM ROS Configuration Manual

for the

RUGGEDCOM RST2228P.

Use the following settings to connect to the port:

Speed

57600 baud

Data Bits

Stop Bit

Parity

None

Flow Control

Off

Terminal ID

VT100

Ethernet Ports

Connect any of the available Ethernet ports on the device to a management switch

and access the RUGGEDCOM RST2228P console and Web interfaces via the device's

IP address. The factory default IP address for the RUGGEDCOM RST2228P is

https://-

192.168.0.2

RUGGEDCOM RST2228P

Installation Manual, 12/2019, C79000-G8976-1403-05

Содержание SIMATIC NET RUGGEDCOM RST2228



























































Результаты поиска

Содержание SIMATIC NET RUGGEDCOM RST2228

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM RST2228

Бренды по названию

Популярные бренды

Siemens SIMATIC NET RUGGEDCOM RST2228, Руководство по установке

Результаты поиска

Содержание SIMATIC NET RUGGEDCOM RST2228

Отзывы:

Похожие инструкции для SIMATIC NET RUGGEDCOM RST2228

Бренды по названию

Популярные бренды