Siemens SICAM Q80 Скачать руководство пользователя страница 148 | Manualshive

Страница: 148 / 240

Siemens SICAM Q80 Скачать руководство пользователя страница 148

148

SICAM Q80 7KG8080

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

5.1.7.2

Autoreport

The program

Autoreport

evaluates in the background the data delivered by the program

Auto-Transfer

. New data are

imported and depending on the settings, a report is generated cyclically for each measurement location. Import of the
data conforms to the procedure on the page

Data transfer

, where there is also entry into the

. This means that these data are available for evaluation and display.

The settings correspond to the

evaluation options

belonging to

SICAM Q80 Manager

under

Extras \ Options \

Evaluation

.

The evaluation is conducted according to defined value limits (the setting for the standards is EN 50160). The reports
are composed in PDF-format. This corresponds to performing the evaluation manually on the page

Network quality

.

-

Start of the automatic data import and report can be performed by

o

the program

Auto-Transfer

, once new data have been transferred from the device

o

cyclically by the Windows Task Manager

o

the Start menu item Run

-

Ending the program

Auto-Transfer

is performed

o

once all data have been imported and no new data have been transferred for 5 minutes

o

by the user

Autoreport Status: Display only - no configuration

The call is made by means of the

Auto-Transfer

as soon as new data have been transferred, or by the

.

In the Topology, you can evaluate the automatically generated results. The possibilities have already been explained
under

Topology / Devices

.

Note

The computations to be performed can take extensive time, especially when there are many
monitoring devices. It is recommended that the Autoreport make use of the Windows Task
Planner to always start whenever there are no other tasks.

106

174

177

115

142

150

21

«
...
146
147
148
149
150
...
»

Содержание SICAM Q80

















































































































































































































































Отзывы:

Нет отзывов