Siemens SICAM Q80 Скачать руководство пользователя страница 106

Страница: 106 / 240

106

SICAM Q80 7KG8080

Power Quality Recorder SICAM Q80 7KG8080, System manual

E50417-H1076-C420-A2, Release 12.01.2015

5.1.4

Manual data transfer

This dialog enables you to conveniently manual transfer of data from the measurement device to the PC, if not set

automatically

. Once the data have been transferred, they are available in the measurement database and can be

investigated in the

evaluation

or in the

channel search

The program

Auto-Transfer

independently performs the data transfer along with the

evaluation

Use

Select device…

to specify the desired

SICAM Q80 7KG8080

unit if you have multiple devices in your

communication network. If you make a change, you exit the current parameter set's context menu and are
prompted to save (if necessary). Subsequently, a default standard parameter set is loaded which is then
displayed in the title bar.

Clicking on

Search hard disk

to read out the contents of the selected measurement device's hard drive. The

function initially starts with a search window while the software prepares a list of all data present on the device
hard drive. The measurement's

Location,

measurement task name, Start time

and

End

are indicated.

If you wish to read-in the data stored on the Compact Flashcard inside a laptop slot, for example, select

Search

PC.

Data transfer selection window

Next. the following options are available:

Selecting data to transfer

: By dragging the entries for data from the upper list to the lower list, data from the

source is transferred to the target. Alternatively, select the desired entries to highlight them and click the button

. If the option

Load transferred data configuration

is active, the configuration values for this measurement are

automatically set after the transfer, so that you can go directly to the evaluation page.

Deleting data

: Highlight the data to be deleted in the upper list and then click

Delete

142

109

133

148

109

Содержание SICAM Q80

















































































































































































































































Результаты поиска

Содержание SICAM Q80

Отзывы:

Siemens SICAM Q80, Системное руководство, Страница: 106 / 240

Результаты поиска

Содержание SICAM Q80

Отзывы: