Siemens Sentron 3VA страница 460 Скачать руководство пользователя | Manualshive

Страница: 460 / 492

background image

Technical specifications

6.4 Derating

3VA molded case circuit breakers with UL and IEC certification

458

Manual, 01/2019, L1V30435333-01

Example
Starting point:
A 3VA5 200 A molded case circuit breaker with a TM230 trip unit is used in a

400 Hz application. The molded case circuit breaker is to trip instantaneously at an

overcurrent of 2000 A.

The maximum permissible rated continuous operational current is calculated first:
200 A · 0.9 = 180 A

The setting value for instantaneous short-circuit protection (I

i

) is then determined on the

basis of the correction factor from the table above:
I

i

= 2000 A · 0.6 = 1200 A

6.4.4

Derating for the electronic trip units of 3VA6 molded case circuit breakers

The ambient temperature has no effect on the current measurement of the electronic trip

units of 3VA6 molded case circuit breakers. The Rogowski coils integrated in the trip unit

measure the current and compare it to the set tripping threshold. Higher or lower ambient

temperatures do not influence the tripping threshold, which means that it is not necessary to

apply correction factors.

Limitation of the rated operational current
The temperature inside the molded case circuit breaker is nonetheless influenced by the

ambient temperature and the current-dependent power loss generated inside the unit. To

prevent overloading of molded case circuit breakers under difficult thermal conditions, the

maximum rated continuous operational current must therefore be limited as a function of the

ambient temperature in some cases:
The tables below contain the maximum rated uninterrupted operational current as a function

of the accessories to be taken into account and the ambient temperature. The operational

current must never exceed the maximum rated operational current of the molded case circuit

breaker.

Note
The values do not apply to all installation situations of the molded case circuit breaker and

may deviate depending upon factors such as cables and busbars, packing density,

ventilation, etc.
Please observe the applicable overriding guidelines (e.g. IEC 61439).

When connecting terminals with control wire tap are used, the total current from the main

circuit and control wire must not exceed the maximum rated operational current of the

molded case circuit breaker.

«
...
458
459
460
461
462
...
»

Содержание Sentron 3VA













































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sentron 3VA

Бренд: Siemens Страницы: 4

Бренд: Siemens Страницы: 3

Бренд: Siemens Страницы: 5

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 5

Бренд: Siemens Страницы: 2

Бренд: Siemens Страницы: 5

Бренд: Siemens Страницы: 4

3VM10 ED Series

Бренд: Siemens Страницы: 6

3VM11 ED1 Series

Бренд: Siemens Страницы: 7

3VL9431-6 30 Series

Бренд: Siemens Страницы: 8

3VL.5.5 - 2KJ Series

Бренд: Siemens Страницы: 7

3VL7710-6 Series

Бренд: Siemens Страницы: 7

Бренд: Siemens Страницы: 6

Бренд: Siemens Страницы: 11

Бренд: Siemens Страницы: 6

3VF 9 624-1FA.0

Бренд: Siemens Страницы: 6

3VF 9 424-1FA .0

Бренд: Siemens Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды