Siemens SCALANCE XB-000 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 102

background image

WARNING

Insufficient isolation of intrinsically safe and non-intrinsically safe circuits

Risk of explosion in hazardous areas
• When connecting intrinsically safe and non-intrinsically safe circuits, ensure that the

galvanic isolation is performed properly in compliance with local regulations (e.g. IEC
60079-14).

• Observe the device approvals applicable for your country.

Notes for use in hazardous locations according to ATEX, IECEx, UKEX and CCC Ex
If you use the device under ATEX, IECEx, UKEX or CCC Ex conditions you must also keep to the
following safety instructions in addition to the general safety instructions for protection against
explosion:

WARNING

Transient overvoltages

Take measures to prevent transient overvoltages of more than 40% of the rated voltage (or
more than 119 V). This is the case if you only operate devices with SELV (safety extra-low
voltage).

WARNING

Suitable cables at high ambient temperatures in hazardous area

At an ambient temperature of ≥ 60 °C, use heat-resistant cables designed for an ambient
temperature at least 20 °C higher. The cable entries used on the enclosure must comply with
the IP degree of protection required by EN IEC / IEC 60079-0, GB 3836.1.

Safety instructions for use in hazardous locations according to UL/FM HazLoc
If you use the device under UL or FM HazLoc conditions, you must also adhere to the following
safety instructions in addition to the general safety instructions for protection against explosion:

WARNING

EXPLOSION HAZARD

You may only connect or disconnect cables carrying electricity when the power supply is
switched off or when the device is in an area without inflammable gas concentrations.

Safety notices when using the device according to ATEX/IECEx and FM
If you use the device under ATEX/IECEx or FM conditions, you must also observe the following
safety notices in addition to the general safety notices for protection against explosion:

Connecting up

6.1 Safety when connecting up

SCALANCE XB-000
Operating Instructions, 01/2022, A2B00077300-11

47

«
...
45
46
47
48
49
...
»

Содержание SCALANCE XB-000







































































































Отзывы:

Нет отзывов

Похожие инструкции для SCALANCE XB-000

Бренд: JCG Страницы: 3

Sure Cross DX70

Бренд: Banner Страницы: 35

SUPERLOADER DLT MAGAZINE

Бренд: Tandberg Data Страницы: 6

DesignCore RVP-TDA3 Series

Бренд: D3 Страницы: 34

RealPort Ethernet 10/100

Бренд: Xircom Страницы: 30

Бренд: Tektronix Страницы: 178

Бренд: QNAP Страницы: 54

JetNet 3508-LVDC

Бренд: Korenix Страницы: 16

Бренд: ZyXEL Communications Страницы: 2

Бренд: iDirect Страницы: 72

Бренд: ivideon Страницы: 11

Бренд: Buffalo Страницы: 2

Бренд: Amit Страницы: 75

Бренд: RadioSPECTRAL Страницы: 2

Бренд: Transition Networks Страницы: 5

Бренд: VERTO Страницы: 48

LN1000 - RELEASE NOTES 8-27-2010

Бренд: Juniper Страницы: 64

ReadyNAS Duo v2

Бренд: NETGEAR Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды