Siemens SCALANCE W786-x Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 68

Siemens SCALANCE W786-x Скачать руководство пользователя страница 24

Mounting

5.5 Mounting with mounting plate

SCALANCE W786-x

24

Operating Instructions, 11/2014, A5E03678337-07

5.5

Mounting with mounting plate

5.5.1

Fitting the mounting plate to a wall

Drilling template

Note
Installation location
The following should be noted with regard to the installation location:

•

Devices with an internal antenna must be aligned according to the characteristics of the

internal antenna (refer to the technical specifications of the antenna --> Radiation pattern

diagrams). Since the internal antennas are integrated in the housing, the location and

alignment of the housing decides the radiation direction of the antennas.

•

There are no restrictions relating to devices without internal antennas.

The location of the holes for fitting the mounting plate to a wall is shown in the following

figure:

Figure 5-6

Drilling template for fitting the mounting plate to a wall

«
...
22
23
24
25
26
...
»

Содержание SCALANCE W786-x





































































Отзывы:

Нет отзывов