Siemens SCALANCE W786-x Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 68

Siemens SCALANCE W786-x Скачать руководство пользователя страница 16

Description

4.3 Reset button

SCALANCE W786-x

16

Operating Instructions, 11/2014, A5E03678337-07

The reset button has the following functions:

●

Restart of the device
To restart the device, press the Reset button briefly.

Note
If you make changes to the configuration and restart immediately afterwards with the

reset button, the changes may be lost. If you restart the device using the WBM (menu

command "System > Restart") or using the CLI (command "restart" in the Privileged

EXEC Modus), the configuration changes are always retained.

●

Loading new firmware
If the normal procedure with the "Load & Save" menu of Web Based Management is

unsuccessful, the reset button can be used to load new firmware. This situation can occur

if there is a power outage during the normal firmware update. You will find more

information in the section "Troubleshooting/FAQ" in the SCALANCE W700 WBM

configuration manual.

●

Restoring the default parameters (factory defaults)
You will find more information is in the section "Restoring the default parameters" in the

SCALANCE W700 WBM configuration manual.

«
...
14
15
16
17
18
...
»

Содержание SCALANCE W786-x





































































Отзывы:

Нет отзывов