manualshive.com logo in svg

Siemens S11, Руководство по обслуживанию, Страница: 8 / 18

Поделиться
Скачать
Siemens S11 Скачать руководство пользователя страница 8

Private Communication Systems

Mobile Phones

  a) Place ringer gasket (1170) on top of ringer on MMI-Board (1010).

b) Insert fixing pin (1090) into MMI-Board (1010).

c) Connect RF-/Control Module (1000) with upper and lower shieldings 

(1060+1050) and plug assembly onto MMI-Board (1010).

d) Connect lower and upper shielding with clamps (1210)
e) Fix spring (1100) on upper shielding (1060).

f) Solder RF-Cable (1150) to pads on RF-/Control Module (1000). 

5.  Screw in 4 long oval head screws (1070) into upper shielding cover (1060) 

(Torque 20 Ncm).

6.  Close handset with lower case (1040).

7.  Turn in 4 short flat head screws (1080) into battery compartment.

8.  Screw in Antenna (1130) (Torque 25 Ncm).

9. Insert SIM-Card-Holder (1160) and battery.

3.4Handset Datecodes

Siemens is using the industrial standard DIN EN 60062 to indicate the production / 
service dates. The code is printed on the IMEI sticker located under the simcard 
reader.

V1.1

8

  PN MP ST

D. Schnoor

04/98

-> YY = Datecode

Содержание S11



















Отзывы:

Нет отзывов