Siemens RUGGEDCOM M969F Скачать руководство пользователя страница 35

Страница: 35 / 56

RUGGEDCOM M969F

Installation Guide

Chapter 5

Technical Specifications

Operating Environment

Tx (dBm)

Mode

Connector

Cable

Type (µm)

Tx λ (nm)

Min

Max

Sensitivity

(dBm)

Saturation

(dBm)

Typical

Distance

(km)

Power

Budget

(dB)

50/125

62.5/125

850

-9.5

-4

-20

0.5

8/125

9/125

1310

-9.5

-3

-22

-3

8/125

9/125

1310

-7

-26

-3

Typical.

Section 5.5

Operating Environment

The RUGGEDCOM M969F is rated to operate under the following environmental conditions.

Ambient Operating

Temperature

-40 to 85° C (-40 to 185° F)

Ambient Storage Temperature

-40 to 85° C (-40 to 185° F)

Ambient Relative Humidity

5% to 95%

Maximum Altitude

Measured from a 30 cm (12 in) radius surrounding the center of the RUGGEDCOM M969F enclosure.

Reduced to -40 to 80 °C (-40 to 76 °F) when equipped with a 100Base-FX, single-mode, 1300 nm, long-reach 90 km port(s).

Non-condensing

Over temperature range of -40 to 85 °C (-40 to 185 °F)

Section 5.6

Mechanical Specifications

Weight

2.86 kg (6.3 lb)

Ingress Protection

IP67

Enclosure

Cast Aluminum

Содержание RUGGEDCOM M969F

























































Результаты поиска

Содержание RUGGEDCOM M969F

Отзывы:

Похожие инструкции для RUGGEDCOM M969F

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM M969F, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM M969F

Отзывы:

Похожие инструкции для RUGGEDCOM M969F

Бренды по названию

Популярные бренды