Siemens RUGGEDCOM i803 Скачать руководство пользователя

Страница: 35 / 40

Certification
6.1.2 ATEX/IEC Ex

•

ANSI/ISA-12.12.01-2007

Non-Incendive Electrical Equipment For Use In Class 1 And 2, Division 2 And Class

3, Divisions 1 And 2 Hazardous (classified) Locations

The device is marked with a CSA symbol that indicates compliance with both

Canadian and U.S. requirements.

Declarations of Conformity are available on SIOS:
•

https://support.industry.siemens.com/cs/ww/en/view/109476357

(General

Safety)

•

https://support.industry.siemens.com/cs/ww/en/view/109476358

(Hazardous

Locations)

The Certificate Body (CB) test certificate is available on SIOS at

https://

support.industry.siemens.com/cs/ww/en/view/109794217

6.1.2

ATEX/IEC Ex

This device meets the requirements of the following ATEX/IEC Ex standards:
•

IEC/EN 60079-15:2005

Electrical Apparatus for Explosive Gas Atmospheres - Part 15: Construction, Test

and Marking of Type of Protection "N" Electrical Apparatus

It is specifically approved for use in hazardous locations defined as:
• EEx nC IIC T4
• Ex II 3 G
• 12-24 VDC, 2A, Class III

6.1.3

European Union (EU)

This device is declared by Siemens Canada Ltd. to comply with essential

requirements and other relevant provisions of the following EU directives:
•

EN 61000-6-2

Electromagnetic Compatibility (EMC) – Part 6-2: Generic Standards – Immunity

for Industrial Environments

•

EN 60825-1

Safety of Laser Products – Equipment Classification and Requirements

RUGGEDCOM i803

Installation Manual, 04/2022, C79000-G8976-1005-07

Содержание RUGGEDCOM i803









































Результаты поиска

Содержание RUGGEDCOM i803

Отзывы:

Похожие инструкции для RUGGEDCOM i803

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM i803, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM i803

Отзывы:

Похожие инструкции для RUGGEDCOM i803

Бренды по названию

Популярные бренды