background image

34 / 46

Siemens

RDF300… / RDF340... / RDF400… / RDF600…  Basic Documentation

CE1P3076.en

Smart Infrastructure

2020-02-21

Handling

5.1 

Mounting and installation

Mount the room controller on the conduit box. Do not mount on a wall in niches or
bookshelves, behind curtains, above or near heat sources, or exposed to direct
solar radiation. Mount about 1.5 m above the floor.

·

  Devices must be mounted on clean, dry indoor place without direct airflow from

a heating / cooling device, and not be exposed to dripping or splashing.

·

  RDF3... / RDF400… : In case of limited space in the conduit box use the

mounting bracket ARG70.3 to increase the headroom by 10mm.

·

  Before removing the front cover, disconnect the power supply.

See the mounting instructions enclosed with the thermostat:
M3076... for RDF3..., RDF4... ; M3063 for RDF600... .

·

  Wiring, protection and earthing must be installed in compliance with local

regulations.

·

  Properly size the cables to the controller, fan and valve actuators for AC 230 V

mains voltage

·

  Use only valve actuators rated for AC 230 V on RDF300… / RDF400… /

RDF600...

·

  The AC 230 V mains supply line must have an external fuse or circuit breaker

with a rated current of no more than 10 A

·

  Isolate the cables of SELV inputs X1-M/X2-M if the conduit box carries AC 230 V

mains voltage

·

  Inputs X1-M or X2-M of different units (e.g. summer/winter switch) may be

connected in parallel with an external switch. Consider overall maximum contact
sensing current for switch rating

Warning!
No internal line protection for supply lines to external consumers
(Q1, Q2, Q3, Yxx)

Risk of fire and injury due to short-circuits!

·

  Adapt the line diameters as per local regulations to the rated value of the

installed overcurrent protection device.

·

  No metal conduits

·

  No cables provided with a metal sheath

·

  Disconnect from supply before opening the cover

Set the controller application via the DIP switches before snapping the front panel
on the mounting base.
After power is applied, the controller carries out a reset during which all LCD
segments flash indicating that the reset was correct. After the reset, which takes
about 3 seconds, the controller is ready for commissioning by qualified HVAC staff.

Mounting /
dismounting

Wiring

Commissioning

Содержание RDF300 Series















































Отзывы: