Siemens QAA73.210 Скачать руководство пользователя страница 6

Страница: 6 / 36

6 / 36

Siemens

Room Unit for Boiler Control

CE1U2283en

Building Technologies

Mounting and Installation

2015-09-16

1.2 Product

liability

The products may only be used in building services plant and applications as

described above

When using the products, all requirements specified under "Technical data"

must be observed

The local regulations for electrical installation must be complied with

1.3 Disposal

The device is classified as waste electronic equipment in terms of the European
Directive 2002/96/EC (WEEE) and should not be disposed of as unsorted muni-
cipal waste.

The relevant national legal rules must be adhered to.
Regarding disposal, use the systems setup for collecting electronic waste.

Observe all local and applicable laws.

Mounting

and

Installation

2.1 Engineering

In the main living room or reference room

The place of installation should be chosen so that the sensor can capture the

room temperature as accurately as possible, without being affected by direct
solar radiation or other heating or cooling sources.

Mounting height is about 1.5 meters above the floor

The unit can be fitted to most commercially available recessed conduit boxes or

directly on the wall.

Mounting location

Содержание QAA73.210





































Результаты поиска

Содержание QAA73.210

Отзывы:

Похожие инструкции для QAA73.210

Бренды по названию

Популярные бренды

Siemens QAA73.210, Руководство пользователя

Результаты поиска

Содержание QAA73.210

Отзывы:

Похожие инструкции для QAA73.210

Бренды по названию

Популярные бренды