Siemens LI60LBC24, Руководство пользователя и инструкции по установке

Страница: 12 / 20

en
Installation instructions
12
11.7 Instructions for the electrical
connection
In order to safely connect the appliance to the elec-
trical system, follow these instructions.
WARNING ‒ Risk of electric shock!
It must always be possible to disconnect the appliance
from the electricity supply. The appliance must only be
connected to a protective contact socket that has been
correctly installed.
▶
The mains plug for the mains power cable must be
easily accessible after the appliance is installed.
▶
If this is not possible, an all-pole isolating switch
must be integrated into the permanent electrical in-
stallation according to the conditions of overvoltage
category III and according to the installation regula-
tions.
▶
The permanent electrical installation must only be
wired by a professional electrician. We recommend
installing a residual-current circuit breaker (RCCB)
in the appliance's power supply circuit.
Sharp-edged components inside the appliance may
damage the connecting cable.
▶
Do not kink or trap the connecting cable.
¡
The connection data can be found on the rating
plate. →
Page 8
¡
The connecting cable is approx. 1.30 m long.
¡
This appliance complies with the EC interference
suppression regulations.
¡
The appliance corresponds to protection class 1.
You should therefore only use the appliance with a
protective earth connection.
¡
Do not connect the appliance to the power supply
during installation.
¡
Ensure that the protection against contact is guaran-
teed during installation.
11.8 Instructions for the exhaust air pipe
The appliance manufacturer does not provide any war-
ranty for faults attributable to the pipeline.
¡
Use a short, straight exhaust air pipe with as large a
pipe diameter as possible.
¡
Long, rough exhaust air pipes, many pipe bends or
small pipe diameters reduce the suction power and
increase the fan noise.
¡
Use an exhaust pipe that is made of non-combust-
ible material.
¡
To prevent condensate from returning, fit the ex-
haust pipe with a 1° gradient from the appliance.
Round pipes
Use round pipes with an inner diameter of 150 mm (re-
commended) or at least 120 mm.
11.9 Instructions for the air extraction mode
For air extraction mode, a one-way flap should be in-
stalled.
Notes
¡
If a one-way flap is not included with the appliance,
one can be ordered from a specialist retailer.
¡
If the exhaust air is conveyed through the external
wall, a telescopic duct should be used.
11.10 Installation
Checking the unit
1.
Check whether the fitted unit is level and has suffi-
cient load-bearing capacity.
The max. weight of the appliance is 6 kg.
2.
Ensure that the fitted unit is heat-resistant up to
90 °C.
3.
Ensure that the fitted unit is still stable after the cut-
outs have been made.
Preparing the units
Requirement:
The unit is suitable for the installation.
→ "Checking the unit", Page 12
1.
Cover the hob to prevent damage.
2.
Ensure that the fitted unit is still stable after the cut-
outs have been made.
3.
Make the cut-out for the exhaust pipe.
4.
When installing in cabinets with an intermediate
floor, make the cut-out in the intermediate floor.
5.
Remove any shavings.
Preparing the appliance
▶
Remove the grease filters.
To avoid causing damage, do not bend the grease
filters.
Installing the appliance
1.
When installing without an intermediate floor, meas-
ure and mark the holes for the mounting brackets
on the side walls.
102
83
2.
When installing with an intermediate floor, slightly
screw the mounting brackets onto the appliance. In-
sert the appliance into the opening in the intermedi-
ate floor. Mark the holes for the mounting brackets
on the side walls. Unscrew the mounting brackets
from the appliance again.
3.
Screw the mounting brackets to the unit. In doing
so, only tighten the screws tight enough that the
mounting bracket can still be moved.