Siemens IQ700 HS658GE 7B Series, Инструкция по эксплуатации

Страница: 27 / 64

en Cleaning function
26
.
Cleaning function
Cleaning function
Your appliance has the "Cleaning function" and
"Descaling" operating modes. The self-cleaning
surfaces in the cooking compartment are cleaned with
the cleaning function. You can use the "descaling"
operating mode to remove limescale from the
evaporator.
Cleaning function
The self-cleaning surfaces (back panel, ceiling panel
and side panels) are coated with a porous, matt
ceramic material. This coating absorbs and breaks
down splashes from baking, roasting and grilling while
the oven is in operation. If the surfaces no longer clean
themselves adequately and dark patches appear, the
surfaces can be cleaned by the cleaning function.
Note: The appliance records the number of times it is
used. The appliance indicates when it has reached a
point in time after which cleaning is recommended. The
recommendation is displayed until the cleaning function
has finished.
If you do not act on this recommendation, the self-
cleaning surfaces may become damaged.
If your appliance is already prematurely very dirty or if
you notice dark patches on the back panel, do not wait
until your appliance recommends cleaning to do so.
This is because the more often the appliance is
cleaned, the longer the self-cleaning surfaces will retain
their cleaning capability. You can clean your appliance
at any time as required using the cleaning function.
Caution!
If your appliance has a steam function, the messages
recommending that you descale the appliance and that
you run the cleaning function may appear at the same
time. Follow the recommendation to descale the
appliance. The recommendation to run the cleaning
function does not appear on the display again until you
have descaled the appliance.
Before running the cleaning function
Remove shelves, rails, accessories and ovenware from
the cooking compartment.
Cleaning the cooking compartment floor and the
inside of the appliance door
Remove the worst dirt from the cooking compartment
floor, the inside of the appliance door and the interior
lighting. Otherwise, patches will appear that can no
longer be removed.
Caution!
Do not use oven cleaner on the self-cleaning surfaces.
This will damage the surfaces. If oven cleaner does get
onto these surfaces, dab it off immediately using water
and a sponge cloth. Do not rub the surface and do not
use abrasive cleaning aids.
:
Warning – Risk of burns!
;
The appliance becomes very hot on the outside
during the cleaning function. Never touch the appliance
door. Allow the appliance to cool down. Keep children
at a safe distance.
Setting the cleaning function
Cleaning lasts 60 minutes.
The duration cannot be changed.
1.
Press the menu button.
The operating modes menu opens.
2.
Select the "Cleaning function" operating mode.
If you touch the "Next" field, information on the
cleaning operation is displayed.
3.
Press the "Start/stop" button to start the cleaning
operation.
You can see the duration counting down in the
status bar.
Keep the kitchen ventilated while cleaning is in
progress.
Once the cleaning has finished
An audible signal sounds. The oven stops heating.
“Finished” appears in the status bar. Use the
0
button
to switch off the audible signal.
Cancelling cleaning
Press the On/Off button. All settings are deleted. You
can implement new settings.
Caution!
The cleaning recommendation is not reset. The
recommendation to run the cleaning function appears
on the display.
You can set the cleaning to run overnight
In the section "Time settings", you can find out how to
delay the end time. This allows you to use the oven at
any time throughout the day.
~
"Time-setting options"
on page 20
Once the cleaning function has finished
Once the cooking compartment has cooled down, wipe
down the cooking compartment with a damp cloth if
necessary.
Note:
During operation and while the cleaning function
is active, reddish patches may form on the surfaces.
This is not rust, but residue from food. These spots are
not harmful and do not impair the cleaning ability of the
self-cleaning surfaces.
Descaling
To ensure that your appliance continues to operate
correctly, it must be descaled regularly.
Beef, medium 60
Beef, well done 70
Lamb 70
Other: Heating/reheating food 65-75
Food Core temperature in
°C
Cleaning agent en
27
Descaling comprises a number of different steps. For
hygiene reasons, the descaling programme must be
run through completely before the appliance is ready
for operation again. In total, the descaling programme
runs for approx. 70–95 minutes.
■
Descale (approx. 55–70 minutes), then empty and
refill the water tank
■
First rinsing cycle (approx. 9–12 minutes), then
empty and refill the water tank
■
Second rinsing cycle (approx. 9–12 minutes), then
empty and dry the water tank
If descaling is interrupted (e.g. due to a power failure or
because the appliance is switched off), you will be
prompted to rinse the appliance twice when you switch
it back on. The appliance cannot be used until the
second rinsing cycle has finished.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
When only another five or fewer steam-assisted
operations are possible, the appliance reminds you to
descale it with a message on the display. The number
of remaining operations is displayed after the appliance
is switched on. You can therefore prepare for the
descaling in good time.
Starting
Caution!
■
Risk of damage to the appliance: Only use liquid
descalers recommended by us for the descaling
programme. The time the product needs to work
during descaling depends on the type of descaler
used. Other descalers may damage the appliance.
Descaler order no. 311 680
■
Descaling solution: Do not allow any descaling
solution or descaler to come into contact with the
control panel or other surfaces on the appliance.
This damages the surfaces. If this does happen,
remove the descaling solution immediately with
water.
If you have used a steam-assisted operation
immediately before descaling, you must first switch the
appliance off so that the residual water is pumped out
of the evaporator system.
1.
Mix 400 ml water with 200 ml liquid descaler to
make a descaling solution.
2.
Press the On/Off button.
3.
Remove the water tank and fill it with descaling
solution.
4.
Once the water tank has been filled with descaling
solution, push it back in again fully.
5.
Close the control panel.
6.
Press the Menu button.
The operating modes menu opens.
7.
Select the "Descaling" operating mode.
If you touch the "Next" field, information on the
cleaning operation is displayed.
The duration of the descaling programme is
displayed. It cannot be changed.
8.
Press the "Start/stop" button to start the cleaning
operation.
The appliance is descaled. You can see the duration
counting down in the status bar. An audible signal
sounds once descaling has finished.
First rinsing cycle
1.
Open the control panel.
2.
Remove the water tank, rinse thoroughly, fill with
water and reinsert.
3.
Close the control panel.
4.
Press the Start/Stop button to start.
The appliance rinses. As soon as the rinsing cycle
has run through, a signal sounds.
Second rinsing cycle
1.
Open the control panel.
2.
Remove the water tank, rinse thoroughly, fill with
water and reinsert.
3.
Close the control panel.
4.
Press the Start/Stop button to start.
The appliance rinses. As soon as the rinsing cycle
has run through, a signal sounds.
Subsequent cleaning
1.
Open the control panel.
2.
Empty and dry the water tank.
3.
Switch off the appliance.
Descaling is complete and the appliance is ready for
use again.
D
Cleaning agent
Cleaning agent
With good care and cleaning, your appliance will retain
its appearance and remain fully functioning for a long
time to come. We will explain here how you should
correctly care for and clean your appliance.
Suitable cleaning agents
To ensure that the different surfaces are not damaged
by using the wrong cleaning agent, observe the
information in the table. Depending on the appliance
model, not all of the areas listed may be on/in your
appliance.
Caution!
Risk of surface damage
Do not use:
■
Harsh or abrasive cleaning agents,
■
Cleaning agents with a high alcohol content,
■
Hard scouring pads or cleaning sponges,
■
High-pressure cleaners or steam cleaners,
■
Special cleaners for cleaning the appliance while it is
hot.
Wash new sponge cloths thoroughly before use.
Tip: Highly recommended cleaning and care products
can be purchased through the after-sales service.
Observe the respective manufacturer's instructions.
:
Warning – Risk of burns!
The appliance becomes very hot. Never touch the
interior surfaces of the cooking compartment or the
heating elements. Always allow the appliance to cool
down. Keep children at a safe distance.