manualshive.com logo in svg

Siemens INOX PRO SIMATIC IPC277D, Руководство по обслуживанию, Страница: 23 / 25

Поделиться
Скачать
Siemens INOX PRO SIMATIC IPC277D Скачать руководство пользователя страница 23

 

SIMATIC IPC277D 19" INOX PRO, SIMATIC IFP1900 INOX PRO 
Service Manual, 03/2015, A5E35751762-AA 

23

 

 

Accessories and spare parts 

5 

 

 

Accessories 

Mounting kit for stand mounting 
A mounting kit is available for stand mounting of the device. Mounting kit contents: 

●

 

1 stainless steel tube with flange: Length 500 mm, outer diameter 48.3 mm, inner 

diameter 40 mm. 

The mechanical interface of the stainless steel tube with flange fits the mechanical 

interface of the device. 

●

 

4 hexagon screws M5×25 made of stainless steel 

●

 

1 flat seal 

Article number 6AV7675-1GB00-0AA0 

Mounting kit for support arm mounting 
A mounting kit is available for support arm mounting of the device. Mounting kit contents: 

●

 

1 stainless steel tube with flange: Length 500 mm, outer diameter 48.3 mm, inner 

diameter 40 mm. 

The mechanical interface of the stainless steel tube with flange fits the mechanical 

interface of the device. 

●

 

1 adapter support arm 

●

 

8 hexagon screws M5×20 made of stainless steel 

●

 

2 flat seals 

Article number 6AV7675-1GB10-0AA0 

Service pack 
The service pack contains: 

●

 

1 spare seal for the terminal compartment cover of the device 

●

 

6 screws for the terminal compartment cover of the device 

●

 

1 spare seal for the mechanical interface of the device 

●

 

4 screws for fastening the stainless steel tube with flange from a mounting kit to the 

mechanical interface of the device 

●

 

1 connecting terminal for the power supply 

●

 

1 terminal block for the terminal strip in the terminal compartment 

●

 

Documentation 

Article number 6AV7675-1JD20-0AA0 

Содержание INOX PRO SIMATIC IPC277D


























Отзывы:

Нет отзывов