manualshive.com logo in svg

Siemens INOX PRO SIMATIC IPC277D, Руководство по обслуживанию, Страница: 14 / 25

Поделиться
Скачать
Siemens INOX PRO SIMATIC IPC277D Скачать руководство пользователя страница 14

Extended maintenance work 

 

4.3 Replacing the seal of the rear panel 

 

SIMATIC IPC277D 19" INOX PRO, SIMATIC IFP1900 INOX PRO 

14

 

Service Manual, 03/2015, A5E35751762-AA 

7.

 

Pull out the plug of the flat ribbon cable from the rear panel electronic as shown in the 

figure below. 

 

8.

 

Place all cables whose plugs you have removed on the rear panel and the front as shown 

in the figure below. 

 

4.3

 

Replacing the seal of the rear panel 

 

 

WARNING 

IP66K degree of protection 
The device has IP66K degree of protection when it is closed. If the rear panel seal is not 

inserted correctly or if the device is not closed properly, IP66K degree of protection is no 

longer guaranteed. Humidity may penetrate the device. The result may be damage to the 

device and personal injury. 
Make sure you follow the instructions in this document precisely when replacing the seal. 

Make sure that the seal is inserted correctly and that the rear panel is fastened properly. 

 

Requirement 

●

 

The device is open. 

●

 

The cables between the front and the rear panel have been removed. 

Содержание INOX PRO SIMATIC IPC277D


























Отзывы:

Нет отзывов