Siemens FDCI222 Скачать руководство пользователя

Страница: 5 / 50

About this document

Applicable documents

5 | 50

Building Technologies

007023_k_en_--

Fire Safety

2017-11-22

1 About this document

Specialist electrical engineering knowledge is required for installation.
Only an expert is permitted to carry out installation work.

Incorrect installation can take safety devices out of operation unbeknown to a

layperson.

Goal and purpose

This document contains all information on the input module FDCI222 and the

input/output modules FDCIO222 and FDCIO224. Following the instructions

consistently will ensure that the product can be used safely and without any

problems.

Scope

The document is valid for the following modules:

Input module FDCI222
Input/output module FDCIO222
Input/output module FDCIO224

Intended use

The input module FDCI222, the input/output module FDCIO222, and the

input/output module FDCIO224 may only be used in one of the following fire

detection systems:

FS20
FS720
FC360

Содержание FDCI222



















































Результаты поиска

Содержание FDCI222

Отзывы:

Похожие инструкции для FDCI222

Бренды по названию

Популярные бренды

Siemens FDCI222, Техническое руководство

Результаты поиска

Содержание FDCI222

Отзывы:

Похожие инструкции для FDCI222

Бренды по названию

Популярные бренды