Siemens DESIGO PX Series Скачать руководство пользователя страница 1

Страница: 1 / 10

223

DESIGO™ PX

System controllers

PXC001.D

PXC001-E.D

PXA40-RS...

for the integration of third-party devices and systems in Desigo

•

Integration platforms and system controllers for third-party devices and

systems via KNX, Modbus, M-Bus and other protocols into the automation

level via BACnet

•

System controllers for the integration of Desigo RXB/RXL room controllers

•

Native BACnet devices with communication via BACnet/LonTalk or

BACnet/IP

•

BTL label (BACnet communications passed the BTL test)

•

Comprehensive management and system functions (alarm management,

time scheduling, trends, remote management, access protection etc.)

•

Supports operation via local or network-compatible operator units PXM…

CM1N9223en_01

2014-04-04

Building Technologies

Содержание DESIGO PX Series











Результаты поиска

Содержание DESIGO PX Series

Отзывы:

Похожие инструкции для DESIGO PX Series

Бренды по названию

Популярные бренды

Siemens DESIGO PX Series, Руководство пользователя

Результаты поиска

Содержание DESIGO PX Series

Отзывы:

Похожие инструкции для DESIGO PX Series

Бренды по названию

Популярные бренды