Siemens CP 1626 Скачать руководство пользователя страница 13

Страница: 13 / 72

Description of the device

CP 1626
Operating Instructions, 11/2018, C79000-G8976-C434-03

The table describes the LED displays that indicate the operating states:

BF LED

SF LED

Description

off

–

Communications connection is established.

–

Link status error has occurred.

flashing slowly

–

There are two possible causes:

•

An IO device cannot be addressed.

•

An IP address was assigned twice.

–

off

No fault/error.

–

Diagnostics information is available.

Alternating slow flashing and flashing of

the 2 port LEDs (yellow and green) of the

X1 interface

Flash test for recognizing the communications processor.

Alternating fast flashing

A disruption has occurred.
In this case, diagnostics via the Web or using SNMP is

no longer possible.
Note
If this error occurs, contact Technical Support. You will

find the contact data in the section "

Preface (Page 3

)".

External power supply

The CP 1626 has a socket for connecting an external power supply.
With this power supply, the integrated real-time switches of the X1 and X2 interfaces can

operate even if the PC is turned off.
It also allows the host PC to be turned on again after being switched off by PROFIenergy.

Ethernet

The CP 1626 is intended for operation in Ethernet networks.
It also has the following features:

●

The connectors are designed for 100BaseTX.

●

Data transmission speed of 100 Mbps in full/half duplex is supported.

●

Autonegotiation (can also be turned off)

●

Autocrossing

Содержание CP 1626









































































Результаты поиска

Содержание CP 1626

Отзывы:

Похожие инструкции для CP 1626

Бренды по названию

Популярные бренды

Siemens CP 1626, Руководство по эксплуатации

Результаты поиска

Содержание CP 1626

Отзывы:

Похожие инструкции для CP 1626

Бренды по названию

Популярные бренды