background image

Configuration and programming 

 

6.2 Information required for configuration 

 

CP 1242-7 V2 

46

 

Operating Instructions, 05/2014, C79000-G8976-C311-00 

General information 

The following information is required for the STEP 7 configuration of the CP 1242-7 GPRS 

V2: 

 

Own phone number of the CP (required for TeleService)   

 

Authorized phone numbers 
Phone numbers of the subscribers that are allowed to send a wake-up call, a wake-up 

SMS or a data SMS to the CP. 

 

APN 
Name of the GPRS access point (APN) of the GSM network provider 

 

APN user name 
User name for the GPRS access point of the GSM network provider 

 

APN password 
Password for the GPRS access point of the GSM network provider 

 

Subscriber number of the SMS center 

 

PIN of the SIM card   

 

 

Note 
Configured PIN and PIN on the SIM card must match. 
If you enter the PIN of the SIM card of the CP 1242-7 GPRS V2 incorrectly during STEP 7 

configuration and download the station, the CP stores the wrong PIN. An incorrectly entered 

PIN is transferred by the CP only once so that the SIM card is not locked. 
If you change the PIN of the SIM card externally to the incorrectly configured PIN (new PIN 

of the SIM card = incorrectly entered PIN in STEP 7), the CP rejects this PIN again without 

checking it. 
 

Solution after entering an incorrect PIN: 
To avoid the PIN being rejected by the CP again, use a PIN that is different from the 

incorrectly entered PIN. Procedure: 

 

If the PIN of the SIM card was not changed: 

 

Configure the PIN in STEP 7 with the PIN of the SIM card. 

 

Reload the station. 

 

If the original PIN of the SIM card was changed externally to the PIN that was previously 

incorrectly entered in STEP 7: 

 

Change the PIN of the SIM card externally to a new PIN that has not yet been 

incorrectly configured in STEP 7. 

 

Change the configured PIN in STEP 7 to the newly assigned PIN of the SIM card. 

 

Reload the station. 

 

Содержание CP 1242-7 GPRS V2









































































Отзывы: