Siemens Cerberus PRO FC721 Скачать руководство пользователя страница 101

Страница: 101 / 118

Commissioning

Detailed commissioning steps

101 | 118

Building Technologies

A6V10211100_f_en_--

Fire Safety

2015-12-15

10.8.10 Freezing outputs

You can freeze outputs with connected fire dampers to prevent them from being

activated if the 'Station' or line is restarted or in the event of a module reset. A

restart is required if a modified configuration is loaded to the 'Station'.

Duration of freeze
The output freeze lasts until the next restart or module reset. It is deactivated after

the restart or module reset. See chapter 'Enabling frozen outputs [➙ 101]' for how

to manually deactivate freezing.

All line devices are switched on.

Input/output modules with connected fire dampers are present on the line.

The output freeze is activated / configured in the ↑ 'Site' configuration. See

document A6V10210424.

1. At the 'Station', select the 'Station', a module, or a line in the hardware tree.
2. Select 'Execute Commands' > 'Freeze selected outputs ON'.
3. The 'Output positions frozen' message is displayed for the frozen outputs.



You can now restart the 'Station' or the line or perform a module reset.

10.8.11 Enabling frozen outputs

One or more outputs have been frozen / the 'Output positions frozen' message

is displayed for one or more outputs.

All line devices are switched on.

1. At the 'Station', in the hardware tree select the 'Station', the module, or the line

that has been frozen or select the 'Output positions frozen' message for the

corresponding element.

2. Select 'Execute Commands' > 'Freeze selected outputs OFF'.



Freezing of the outputs is deactivated.

Содержание Cerberus PRO FC721























































































































Результаты поиска

Содержание Cerberus PRO FC721

Отзывы:

Похожие инструкции для Cerberus PRO FC721

Бренды по названию

Популярные бренды

Siemens Cerberus PRO FC721, Техническое руководство

Результаты поиска

Содержание Cerberus PRO FC721

Отзывы:

Похожие инструкции для Cerberus PRO FC721

Бренды по названию

Популярные бренды