manualshive.com logo in svg

Siemens Cerberus NW8005, Техническое руководство

Поделиться
Скачать
Siemens Cerberus NW8005 Скачать руководство пользователя страница 18

14

Siemens Building Technologies
Cerberus Division

e3180a.doc

12.2000

5.1.4 

Erasing the result memory

➜

 

Press keys simultaneously for longer than 1 sec.

➜

 

Press key once again for confirmation

5.2 

Preparations in the field

1. 

The data line must not be live.

2. 

All bus nodes must be removed from the data line. No electronic components must
be connected to the data bus.

3. 

The individual segments of the data link must be interconnected.

4. 

The SLT-22 device is connected to terminals "Pair1" near end.

5. 

The SLT-11 device is connected to terminals "Pair1" far end.

5.2.1 

Commissioning of the test set

Connect test specimen

The devices are connected using the safety cables and safety clips supplied. Terminals

Pair1

 are used on both devices.

The SLT-22 device is used as actuating device (Master) at the near end and the SLT-
11 device (Slave) at the far end.

Содержание Cerberus NW8005

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды