manualshive.com logo in svg

Siemens CAZBHS, Установка, эксплуатация и обслуживание

Поделиться
Скачать
Siemens CAZBHS Скачать руководство пользователя страница 28

- 27 - 

Maintenance

 

Shaft or Flange Face Runout 

Because inspection of flange faces, eccentricity and 
shaft runout is rigorously enforced at the factory, 
vibrations caused by this alignment problem are rare 
and usually if shaft runout, face runout, or eccentricity 
are excessive; the equipment has been mistreated in 
some way. 
 
The method for checking shaft and flange faces is as 
follows: 
 

NOTE

 

On antifriction bearings, it is recommended that the 
test be made with the shaft vertical to minimize the 
effect of bearing clearances. 

 

Shaft Runout 

The shaft runout is measured with the indicator 
stationary with respect to the machine and with its 
point at the end of the finished surface of the shaft.  
See Figure 13 for typical fixture. 
 
Read the maximum and minimum values on the 
indicator as the shaft is rotated slowly through 360 
degrees.  The difference between the readings shall 
not exceed 0.003 inches. 
 

 

Eccentricity and Face Runout of 
Mounting Surfaces 

The eccentricity and face runout of the mounting 
surfaces is measured with indicators mounted on the 
shaft extension.  The point of the eccentricity 
indicator shall be at approximately the middle of the 
rabbet surface, and the point of the face runout 
indicator shall be approximately the outer diameter of 
the mounting face.  See Figure 14  for typical fixture. 
Read  the maximum and minimum values on the 
indicators as the shaft is rotated slowly through 360 
degrees.  The difference between the readings shall 
not exceed 0.007 inches. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

Figure 13 – Shaft Runout Check 

Figure 14 – Eccentricity and Face Runout Check 

 
 
 
 
 

 

Содержание CAZBHS







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды