manualshive.com logo in svg

Siemens CAZBHS, Установка, эксплуатация и обслуживание

Поделиться
Скачать
Siemens CAZBHS Скачать руководство пользователя страница 21

- 20 - 

Maintenance 

 

Bearing Lubricants - Oil 

SSU at 

100

°

F 

Typical 

Oil 

ISO VG 

Bearing Type 

300-350 

68 

Antifriction Bearing 

700-800 

150 

Spherical Roller 

300-350 

68 

Kingsbury 

300-350 

68 

Sleeve Guide Bearing 

 

The preceding table lists “typical” lubricating oils only.  
See the lubrication plate mounted on the motor for 
the correct oil and relubrication frequency for your 
motor. 
Before starting the machine, fill bearing chamber to 
the correct oil level as indicated on the motor outline 
drawing. Always fill through the pipe or plug at the 
side of the motor. Do not overfill, as the oil may then 
escape along the shaft and enter the unit. To change 
oil, drain the oil reservoir by removing the pipe plug. 
Clean and flush with solvent and refill with fresh 
filtered oil every three to twelve months, depending 
upon severity of service. Use a high grade turbine oil 
having a viscosity indicated on the motor lubrication 
data plate.. 

 

Always correct oil or water leaks and replace lost 
lubricant promptly. 

 

CAUTION

 

Improper oil level reading may cause improper 
lubrication of machine. 

 

Avoid adding oil while unit is running. 

 

Bearing Replacement 

Replacement bearings may be of a different 
manufacturer; but must be equal to the originals used 
on the motor.  See nameplate on unit or outline 
drawing for bearing numbers.  When ordering 
bearings specify as follows: 
1.  Identify numerals and manufacturer stamp on the 

bearing (number is also on motor nameplate). 

2.  Bearing Tolerance Class, i.e. (A.B.E.C.-1) 

Annular Bearing Engineer’s Committee - 
Tolerance Class One. 

3.  Electric motor quality. 
4.  If deep groove bearings, specify the internal 

radial clearance, i.e. (A.F.B.M.A.-3) Antifriction 
Bearing Manufacturers Association, Clearance 
Class Three. 

5.  Angular contact type bearing replacements must 

be equivalent in angle of contact.  40% contact 
angle is standard. 

6.  The complete A.F.B.M.A. bearing number from 

the motor nameplate. 

 

 
Spherical Roller Bearings

 

 
External thrust transmitted from the driven unit is 
normally carried by the top bearing.  If replacement is 
necessary, the new bearing must be  the same type 
as the original (See Figure 5).  
 
 
 

 

Figure 5 

 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание CAZBHS







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды