Siemens 6GK7 542-1AX00-0XE0 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 54

background image

Installation, connecting up, commissioning, operation

3.1 Important notes on using the device

CM 1542-1

22

Operating Instructions, 07/2019, C79000-G8976-C355-04

WARNING

EXPLOSION HAZARD
Do not connect or disconnect cables to or from the device when a flammable or

combustible atmosphere is present.

WARNING

EXPLOSION HAZARD
Replacing components may impair suitability for Class 1, Division 2 or Zone 2.

WARNING

When used in hazardous environments corresponding to Class I, Division 2 or Class I,

Zone 2, the device must be installed in a cabinet or a suitable enclosure.

3.1.2

Notices on use in hazardous areas according to ATEX / IECEx

WARNING

Requirements for the cabinet/enclosure
To comply with EC Directive 2014/34 EU (ATEX 114) or the conditions of IECEx, this

enclosure or cabinet must meet the requirements of at least IP54 (in compliance with

EN 60529) according to EN 60079-7.

WARNING

Cable
If the cable or conduit entry point exceeds 70 °C or the branching point of conductors

exceeds 80 °C, special precautions must be taken. If the equipment is operated in an air

ambient in excess of 50 °C, only use cables with admitted maximum operating temperature

of at least 80 °C.

WARNING

Take measures to prevent transient voltage surges of more than 40% of the rated voltage.

This is the case if you only operate devices with SELV (safety extra-low voltage).

«
...
20
21
22
23
24
...
»

Содержание 6GK7 542-1AX00-0XE0























































Отзывы:

Нет отзывов

Похожие инструкции для 6GK7 542-1AX00-0XE0

CQ-C7413U? CQ-C7113U

Бренд: Panasonic Страницы: 22

Бренд: Polk Audio Страницы: 8

Бренд: PURE Страницы: 88

Бренд: Magnavox Страницы: 23

Бренд: Caliber Страницы: 18

Бренд: JBL Страницы: 11

Бренд: Micronix Страницы: 16

151 Musiccenter

Бренд: Burmester Страницы: 20

Бренд: Multilaser Страницы: 25

Бренд: Paso Страницы: 8

MICHELANGELO BT A 60

Бренд: BFT Страницы: 84

Бренд: Curtis Страницы: 7

Бренд: Honeywell Страницы: 30

Бренд: Honeywell Страницы: 28

QUIETPRO QP100Ex

Бренд: Honeywell Страницы: 28

Бренд: Honeywell Страницы: 59

THALES MCS-4200

Бренд: Honeywell Страницы: 200

Бренд: JVC Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды