Siemens 6ES7 410-5FM08-0AB0 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 34

Siemens 6ES7 410-5FM08-0AB0 Скачать руководство пользователя страница 25

Connecting up

6

6.1

Safety when connecting up

Safety notices

When connecting up the device, keep to the safety notices listed below.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

EXPLOSION HAZARD
Do not connect or disconnect cables to or from the device when a flammable or combustible

atmosphere is present.

Safety notices for use according to ATEX and IECEx
If you use the device under ATEX or IECEx conditions you must also keep to the following

safety notices in addition to the general safety notices for protection against explosion:

WARNING

Take measures to prevent transient voltage surges of more than 40% of the rated voltage.

This is the case if you only operate devices with SELV (safety extra-low voltage).

WARNING

Provisions shall be made to prevent the rated voltage from being exceeded by transient

disturbances of more than 119 V.

Synchronization modules for S7-400H

Equipment Manual, 04/2020, A5E50072434-AA

25

«
...
23
24
25
26
27
...
»

Содержание 6ES7 410-5FM08-0AB0



































Отзывы:

Нет отзывов