Siemens 6EP4131-0GB00-0AY0 Скачать руководство пользователя страница 232 | Manualshive

Страница: 232 / 264

background image

Installation

7.9 Service life of the batteries and handling

SITOP UPS1600 / BAT1600 / UPS1100

232

Equipment Manual, 07.2021, A5E37775406-11-76

7.9.4

Correct storage and transport

SITOP BAT1600 Pb battery module

Article number: 6EP4133-0GA00-0AY0, 6EP4135-0GE00-0AY0 and 6EP4137-0GE00-0AY0
To achieve an optimum lifetime of the battery module, this should be stored for the shortest

possible time in a dry and cool environment that is frost-free.
Never store Pb batteries in completely enclosed containers. During long-term storage, always

ensure that air is circulated as a result of the low levels of gas that are discharged. For long-

term standalone storage, it should be noted that SITOP BAT1600 Pb battery modules are fully

charged cyclically in order to avoid deep discharge of the installed lead batteries. When

stored at room temperature at 25 °C, the recommended recharge interval is approximately

every 6 months; when stored at higher ambient temperatures, the recharge interval must be

shortened to 3 months. At room temperature, the recommended charge parameters for a full

charge are:
•

Charge voltage 27.3 V, current limited to max. 0.4 CA (e.g.: 3.2 Ah Pb … charge current =

1.3 A); charge duration min. 12 hours.

For long-term storage in a system that is not being used – i.e. in a completely wired but

deactivated state – then the application should be cyclically commissioned (depending on the

battery size, every 1 - 4 months) in order to avoid deep discharge of the installed lead

batteries. The recharge interval can be extended to approximately 6 months if the fuse in the

battery module is removed. When stored at increased ambient temperatures, then the

reduced recharge intervals listed above must always be applied.
Before transporting and shipping the SITOP BAT1600 Pb battery module, the prewired plug-in

terminals should be withdrawn and the fuse removed. In international transport legislation,

lead batteries are classified as "hazardous goods" according to UN 2800. The applicable

national and international hazardous goods regulations must be carefully complied with

corresponding to the type of transport selected!

«
...
230
231
232
233
234
...
»

Содержание 6EP4131-0GB00-0AY0









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренд: Parkside Страницы: 640

Бренд: Parkside Страницы: 60

Бренд: Wacker Neuson Страницы: 42

Бренд: Elenco Electronics Страницы: 8

Бренд: Gallagher Страницы: 76

Бренд: Avdel Страницы: 3

Бренд: Michigan Pneumatic Tool Страницы: 16

Бренд: Scheppach Страницы: 48

Бренд: Ryobi Страницы: 124

Бренд: Puls Страницы: 2

Бренд: Universal Tool Страницы: 8

Josef Kihlberg B560

Бренд: Signode Страницы: 56

Бренд: IAN CANADA Страницы: 15

Бренд: Stanley Страницы: 24

Бренд: Precision matthews Страницы: 29

GLASSMAN EJ Series

Бренд: XP Страницы: 59

Бренд: VWR International Страницы: 174

Бренд: Sealey Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды