Siemens 6EP4131-0GB00-0AY0 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 264

background image

Safety and security

1.1 General safety instructions

SITOP UPS1600 / BAT1600 / UPS1100

14

Equipment Manual, 07.2021, A5E37775406-11-76

1.1.1

SITOP BAT1600 and UPS1100

NOTICE

The maintenance, installation and commissioning may only be performed or monitored by

personnel who are familiar with batteries and the necessary precautionary measures.

Ensure that non-authorized personnel do not get involved with these batteries.
When storing, installing and operating the battery modules, the regulations of VDE 0510

Part 2 / EN 50272-2 or the applicable national regulations must be complied with.
For lead-gel batteries, it must be carefully ensured that the battery module location is

adequately ventilated.
Battery module location: In the lower part of the control cabinet or at the coolest location in

the control cabinet to optimize the battery service life.
Dimension the power cables corresponding to the fuse in the battery module.
The fuse should only be inserted in the fuse holder when commissioning the device.
The "+" and "-" power connections of the battery module may

only

be connected to the

UPS1600 UPS module, or when BAT1600 or UPS1100 battery modules of the same type are

connected in parallel.

Do not connect the power connections with "0 V" or "Ground" of

the power supply system!

Only connect battery modules in parallel if they have the same charge state.
When replacing the batteries, always use batteries with the same batch number and

approximately the same charge state. Only the types listed in Section "Battery replacement"

should be used. The approval becomes null and void if other batteries are used.
The batteries must always be disposed of in the discharged condition according to the

applicable regulations.

«
...
12
13
14
15
16
...
»

Содержание 6EP4131-0GB00-0AY0









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренд: U-Line Страницы: 3

CYBERCORE 1000 PLATINUM

Бренд: XPG Страницы: 50

Бренд: Image Industries Страницы: 32

Бренд: Oben Страницы: 32

EPSITRON 787-602

Бренд: WAGO Страницы: 2

Бренд: HOKUBEMA Страницы: 69

Бренд: EINHELL Страницы: 56

Бренд: GOAL ZERO Страницы: 40

Бренд: SilverStone Страницы: 6

Бренд: Rapid Страницы: 20

Бренд: YASKAWA Страницы: 35

Бренд: Hama Страницы: 24

Бренд: Westfalia Страницы: 18

Бренд: HENRY Страницы: 8

Бренд: Kango Страницы: 38

S8JX-P300 Series

Бренд: Omron Страницы: 2

Бренд: Rath Страницы: 6

Бренд: Wealtec Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды