Siemens 1PH728 Скачать руководство пользователя страница 63

Страница: 63 / 82

Maintenance

7.3 Corrective Maintenance

A5E00177602A AD
Siemens AG Operating Instructions 2.02 1PH728

NOTICE

Always disassemble the speed sensor before you dismantle the three-phase motor, in

order to prevent it from becoming damaged.

To disassemble the speed sensor, proceed as follows:
1.

Screw off the sensor cover.

Detach the electrical connection.
–

Pull the cable carefully out of its holder.

–

Pull out the connector.

Remove the screw connections holding the sensor on the end shield.

Pull the sensor off the shaft with the aid of a puller. There are two ways of doing this:

ແ

ໂ

Figure 7-4

Disassembling the speed sensor: forcing off, 1st option

①

Unscrew the screw M5x50.

②

Screw in the screw M5x10 and the screw M6x70 one after the other. This releases

the sensor cone in the motor shaft.

③

Remove the sensor.

FD¡¡

ແ

ໂ

Figure 7-5

Disassembling the speed sensor: forcing off, 2nd option

Siemens Hardware

Содержание 1PH728



















































































Результаты поиска

Содержание 1PH728

Отзывы:

Похожие инструкции для 1PH728

Бренды по названию

Популярные бренды

Siemens 1PH728, Руководство по эксплуатации

Результаты поиска

Содержание 1PH728

Отзывы:

Похожие инструкции для 1PH728

Бренды по названию

Популярные бренды