manualshive.com logo in svg

Siemens 1PH728, Руководство по эксплуатации

Поделиться
Скачать
Siemens 1PH728 Скачать руководство пользователя страница 36

Transport, assembly, and connection 

 

3.3 Electrical connection 

 

A5E00177602A AD 

34

 

Siemens AG  Operating Instructions 2.02  1PH728 

3.3.4

 

Connecting the fan 

Safety notes 

Please observe the following safety instructions relating to connecting a fan: 

 

CAUTION 

 

Only operate the motor with fan 
If the motor is operated without fan it will overheat because the heat that is generated 

cannot be dissipated. Destruction of the motor is the consequence. 
Provide a protective circuit that prevents the main motor from being switched on when the 

fan unit is not in operation. 

 

CAUTION 

 

An external fan is only suitable for one direction of rotation 
The separately-driven fan unit is only designed for one direction of rotation corresponding 

to the direction of rotation arrow. Operation with the wrong direction of rotation can cause 

overheating or destruction of the motor.  
Ensure that the external fan is operated in the proper direction of rotation. The direction-of-

rotation arrow and the direction of movement of the fan impeller are indicated on the rear 

side of the blower. 
If necessary, switch the direction of rotation by swapping over two phase conductors in the 

terminal box. 

 

Connection 

Connect the fan in the terminal box of the fan motor.  

ແ

 

Figure 3-4 

Detailed view of fan, ① fan unit terminal box 

[ID: 337.02] 

Содержание 1PH728



















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды