manualshive.com logo in svg

Siemens Nixdorf D818, Техническое руководство, Страница: 22 / 26

Поделиться
Скачать
Siemens Nixdorf D818 Скачать руководство пользователя страница 22

 Error 

messages

CMOS System Options Not Set

The entries stored in CMOS RAM are incorrect or not complete. Check the
entries in the setup menu.

CMOS Time and Date Not Set

Time and date are not set in setup menu. Call up the setup menu and enter
the correct time and date.

Diskette Boot Failure

The disk in the drive A: is not a boot diskette or is defective. It cannot be
used to boot the system. Insert a system floppy disk in the drive and follow
the instructions displayed on the screen.

Display Memory Read/Write Error

The system CRT controller is missing or its memory is faulty.

Display Switch Not Proper

The setting of jumper J13H3 for the CRT controller is incorrect.

DMA Bus Time-out

A device has driven the bus signal for more than 7.8 Microseconds.

DMA Error

Error in DMA controller.

DMA #1 Error

Error in the first DMA channel.

DMA #2 Error

Error in the second DMA channel.

FDD Controller Failure

The BIOS cannot communicate with the floppy disk drive controller. Check
the entry for 

On-Board Floppy Drive

 in the setup menu and all connections to

the floppy disk drive controller.

A26361-D818-Z120-1-7619

 

33

Error messages 

HDD Controller Failure

The BIOS cannot communicate with the hard disk drive controller. Check the
entry for 

On-Board IDE Drive

 in the setup menu and all connections to the

floppy disk drive controller.

INTR #1 Error

Interrupt channel 1 failed.

INTR #2 Error

Interrupt channel 2 failed.

Invalid Boot Diskette

The disk in the drive A: is not a boot diskette or is defective. Insert a system
floppy disk in the drive.

I/O Card Parity Error at xxxxx

The memory on an expansion card failed. If the address can be determined,
it is displayed as xxxx. If not, the message is 

I/O Card Parity Error

????

.

Keyboard Error

There is a timing problem with the keyboard. Set the 

keyboard

 option in the

setup menu to 

Not Installed

.

Keyboard Is Locked...Unlock It

The keyboard lock on the system is engaged. The system must be unlocked
to continue.

KB/Interface Error

The keyboard cable is defective or not properly connected. Check the
connections of the keyboard or change the keyboard cable.

Memory Parity Error at xxxxx

Memory failed. If the address can be determined, it is displayed as xxxx. If
not, the message is 

I/O Card Parity Error ????

.

OFF BOARD PARITY ERROR ADDR (HEX) = (XXXX)

Parity error in memory installed in an expansion slot.

XXXX

 is the hex address where the error occurred.

34

 

A26361-D818-Z120-1-7619

Содержание D818



























Отзывы:

Нет отзывов