Siemens Healthcare XPRECIA STRIDE Скачать руководство пользователя страница 37

Страница: 37 / 59

Xprecia Stride

User Guide

5. Performing troubleshooting and maintenance

Warning messages

CODE MESSAGE

PROBABLE CAUSE

POSSIBLE SOLUTION

01-13

Test strip or LQC vial not valid

Stride encountered an unknown error
scanning the test strip or vial.

Scan the test strip or vial again. If the error continues,
cancel the test and repeat using a new test strip from
the vial.

01-16

Data integrity error

Stride encountered an unknown
internal error.

Turn Stride on and off.

Error messages

CODE MESSAGE

PROBABLE CAUSE

POSSIBLE SOLUTION

02-01

Apply sample timeout

You didn't apply the sample within 2 minutes.

Redo the test and apply the sample when
prompted by Stride.

02-02

Used test strip inserted

You attempted to use an already processed test
strip.

Discard test strip and restart test with a new strip.

02-03

Early fill error

You attempted to apply a patient or QC sample
before Stride was ready.

Redo the test and only apply the sample when
prompted by Stride.

02-04

Early test strip ejection

You ejected the test strip before Stride was finished
processing the results.

Discard test strip and restart test with a new strip.

02-05

Expired test strip

The test strip is beyond the expiration date.

Verify the Stride date setting is correct and then
redo the test using a test strip from a new vial.

02-07

Test strip port protective cap
removed

You removed the test strip port protective cap
during a test.

Align tab in cap with slot and slide cap until it clicks
into place.

Redo the test with a new strip.

02-08

Test aborted

You canceled a test in progress.

Redo the test with a new strip.

02-09

Critical battery level

Your batteries are almost out of power.

Replace with 3 new AA batteries.

02-10

Communications error

Stride encountered an unknown
communication error.

If you are connected to a PC, disconnect the USB
cable and then reconnect it again to the PC.

If you are upgrading the Stride firmware, cancel
and restart the upgrade.

02-11

Heater control error

Stride encountered an error with the internal heater.

Turn Stride off and on. If the error persists, you may
need to replace the Stride analyzer.

Содержание XPRECIA STRIDE




























































Результаты поиска

Содержание XPRECIA STRIDE

Отзывы:

Siemens Healthcare XPRECIA STRIDE, Руководство пользователя, Страница: 37 / 59

Результаты поиска

Содержание XPRECIA STRIDE

Отзывы: