manualshive.com logo in svg

SICK T4000 Direct Unicode, Руководство по эксплуатации

Поделиться
Скачать
SICK T4000 Direct Unicode Скачать руководство пользователя страница 23

6

Electrical installation

6.1

Safety

DANGER

Hazard due to electrical voltage
Hazard due to unexpected starting of the machine

b

Make sure that the machine is and remains disconnected from the power supply
during the electrical installation.

b

Make sure that the dangerous state of the machine is and remains switched off
during electrical installation.

b

Make sure that the outputs of the safety switch have no effect on the machine
during electrical installation.

DANGER

Incorrect safety switch connection
Loss of safety function

b

When using insulation material or stranded connection wires, make sure they
demonstrate the required temperature resistance and mechanical load capability.

b

Use only safe contacts for safety functions.

DANGER

Hazard due to lack of effectiveness of the protective device
The dangerous state may not be stopped in the event of non-compliance.
Application diagnostic outputs must not be used as safety outputs.

b

All electrical connections must be isolated from the mains supply either by safety
transformers (EN 61558-2-6) or equivalent isolation measures.

b

Use protected cable routing to prevent the risk of cross-circuits and short-circuits.

b

All output contacts must have an adequate suppressor circuit for capacitive and
inductive loads.

b

Provide external contact fuse protection for relay outputs, 

see "Technical data",

page 36

.

b

Provide safety outputs (relay outputs) 13/14 and 23/24 with external fuse protec‐
tion (use fuse 6 A gG or miniature circuit-breaker 6 A with characteristic B or C).

6.2

Notes on cULus

For use according to the requirements of UL 508, the following conditions must be met:

■

The voltage supply must correspond to Class 2 in accordance with UL 508:

°

Galvanically isolated power supply unit with a maximum open-circuit voltage
of 30 V DC and a limited current of max. 8 A

°

Galvanically isolated power supply unit in combination with a fuse in accor‐
dance with UL 248. This fuse should be rated for max. 3.3 A and be inte‐
grated in the 30 V DC voltage section.

■

Only copper with a temperature resistance of at least 75 °C must be used as the
cable material.

ELECTRICAL INSTALLATION 

6

8022726/2019-05-07 | SICK

O P E R A T I N G   I N S T R U C T I O N S | T4000 Multi

23

Subject to change without notice

Содержание T4000 Direct Unicode

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды