SICK MPS-G Скачать руководство пользователя

Страница: 20 / 50

Electrical installation

6.1

Safety

6.1.1

Notes on electrical installation

CAUTION

Danger due to incorrect supply voltage!

An incorrect supply voltage may result in injuries from electric shocks and/or damage to

the device.

■

Only operate the sensor with safety/protective extra-low voltage (SELV/PELV).

NOTICE

Sensor damage or unpredictable operation due to working with live parts.

Working with live parts may result in unpredictable operation.

■

Only carry out wiring work when the power is off.

■

Only connect and disconnect electrical connections when the power is off.

■

The electrical installation must only be performed by electrically qualified person‐

nel.

■

Standard safety requirements must be observed when working on electrical sys‐

tems!

■

Only switch on the supply voltage for the device when the connection tasks have

been completed and the wiring has been thoroughly checked.

■

When using extension cables with open ends, ensure that bare wire ends do not

come into contact with each other (risk of short-circuit when supply voltage is

switched on!). Wires must be appropriately insulated from each other.

■

Wire cross-sections in the supply cable from the user’s power system must be

designed in accordance with the applicable standards. When this is being done in

Germany, observe the following standards: DIN VDE 0100 (Part 430) and DIN VDE

0298 (Part 4) and/or DIN VDE 0891 (Part 1).

■

Circuits connected to the device must be designed as SELV circuits (SELV = Safety

Extra Low Voltage).

■

Protect the device with a separate fuse at the start of the supply circuit.

The IP enclosure rating for the sensor is only achieved if the connected cable is com‐

pletely screwed in.

6.1.2

Wiring instructions

NOTE

Pre-assembled cables can be found online at:

www.sick.com/mps-g

Please observe the following wiring instructions:

■

During installation, pay attention to the different cable groups. The cables are

grouped into the following four groups according to their sensitivity to interference

or radiated emissions:

Group 1: Cables very sensitive to interference, such as analog measuring

cables

Group 2: Cables sensitive to interference, such as sensor cables, communi‐

cation signals, bus signals

ELECTRICAL INSTALLATION

O P E R A T I N G I N S T R U C T I O N S | MPS-G with 2 / 3 switching points and IO-Link (up to 16 switching points)

8025942/2020-07-16 | SICK

Subject to change without notice

Содержание MPS-G



















































Результаты поиска

Содержание MPS-G

Отзывы:

Похожие инструкции для MPS-G

Бренды по названию

Популярные бренды

SICK MPS-G, Руководство по эксплуатации

Результаты поиска

Содержание MPS-G

Отзывы:

Похожие инструкции для MPS-G

Бренды по названию

Популярные бренды