manualshive.com logo in svg

SICK DUSTHUNTER SP100 Ex-2K, Руководство по эксплуатации, Страница: 60 / 130

Поделиться
Скачать
SICK DUSTHUNTER SP100 Ex-2K Скачать руководство пользователя страница 60

60

8024493/AE00/V1-0/2020-09| SICK

O P E R A T I N G   I N S T R U C T I O N S  | DUSTHUNTER SP100 Ex-2K

Subject to change without notice

7

ELECTRICAL INSTALLATION 

Fig. 28: Interface options MCUDH Ex-3K based on using the RS485 output

Safe area

Remote modules

Service inter-

face RS485

Optional Interface module: 

Modbus ASCII/RTU using

the RS485 output

Option 1 - Sopas via USB:

Sopas Service Kit (2097408)

and plug adapter (6075779)

Option 2 - Sopas via Interface module with 

separate 24 V supply:

Ethernet CoLa-B Module(2069666)

and power supply unit 24 V (6075027)

Option 1 - Sopas via USB:

Sopas Service Kit (2097408)

and plug adapter (6075779)

Option 2 - Sopas via Interface module with 

separate 24 V supply:

Ethernet CoLa-B Module (2069666)

and power supply unit 24 V (6075027)

Option 3 - Interface module with separate 

24 V supply:

Ethernet Modbus TCP/IP Module 

(2069664)

and power supply unit 24 V (6075027)

Содержание DUSTHUNTER SP100 Ex-2K



































































































































Отзывы:

Нет отзывов