6
Commissioning
6.1
Setting the zero angle position
The zero angle position between the sensor and magnet can be set either via the cable
or IO-Link.
Setting the zero point via cable:
1.
Connect pin 2 to the voltage supply “L+” for at least two seconds.
2.
LED 1 begins to flash
3.
Within 3 seconds connect pin 2 to ground or leave the connection open (unde‐
fined level)
4.
Position successfully taught in. LED 1 lights up constantly for five seconds
5.
If the position was not successfully taught in, LED 1 flashes quickly for five sec‐
onds
✓
The sensor is adjusted and ready for operation.
To configure the device via an IO-Link procedure, read the MAS IODD, document num‐
ber #8024987. A description of the IODD can be found in the Technical Information,
document number #8027789.
The documents are available on the MAS product page in the Internet
PRODUCT NUMBER.
7
Troubleshooting
The Troubleshooting table indicates measures to be taken if the sensor stops working.
Table 8: Troubleshooting
LED/fault pattern
Cause
Measures
Green LED does not light up
Voltage interruptions outside
the permissible range
Ensure there is a stable power
supply in accordance with the
technical specifications
Yellow LEDs are flashing.
No magnet detected.
Place the magnet on the
active surface of the sensor.
Green LED is pulsating.
IO-Link communication
-
All LEDs are flashing quickly.
Find me
function is activated
-
8
Disassembly and disposal
The sensor must be disposed of in line with applicable country-specific regulations.
When disposing of them, you should try to recycle them (especially the precious met‐
als).
OPERATING INSTRUCTIONS
8027419.1GGF/2022-07-01 | SICK
O P E R A T I N G I N S T R U C T I O N S | MAS
25
Subject to change without notice
en
Содержание 2126478
