SICK 1 075 638 Скачать руководство пользователя страница 48

Страница: 48 / 70

Parameter

Factory setting

ObSB > Q2 teach-in:
Q2, Q2 not

ObSB > manual Q2 teach-in:
-1,000.0 mm ... +1,000.0 mm

+400.0 mm

ObSB > Q2 active status:
High, Low

High

ObSB > Q2 hysteresis:
0000.0 mm ... +0100.0 mm

+1.0 mm

ObSB > Q2 ObSB tolerance
-1,000.0 mm ... +1,000.0 mm

+4.0 mm

ObSB > delay mode:
Off, switch-on delay, switch-off delay, switch-on/switch-off delay, 1
shot

Off

ObSB > time for delay mode:
0000 ms ... 9,999 ms

100 ms

8.4.2.5

Off

When the

Off

output function is activated, output 2 does not have any function and is

therefore deactivated.

8.4.3

In1 input

8.4.3.1

Notes on the input functions

8.4.3.1.1

Description

The In1 input is used for the following tasks:

■

Configuration of various device parameters,

see "Teach-in", page 50

■

Switching the laser on or off at defined times

If the function is set to

Teach

(factory setting), the specific parameters or different mea‐

sured value hold functions can be configured by creating signal levels of different
lengths at pin 5. If the function is set to

Laser off

, when a signal is created the laser is

switched off for the duration of the created signal.

The In1 input must be active in order to be used accordingly (every setting apart from

Off

). The

Off

setting deactivates the input and, therefore, all functions.

NOTE

Deactivating the input is possible only via the display, SOPAS ET, or IO-Link, but not via
the input itself.

The input behavior can be selected as normally open (High Active, factory setting) or
normally closed (Low Active). When

Laser off

is used, the logic also determines whether

the creation of a signal at the input causes the laser to switch off (factory setting) or on.

OPERATION VIA DISPLAY

O P E R A T I N G I N S T R U C T I O N S | OD1000

8019642/18JN/2020-07-01 | SICK

Subject to change without notice

Содержание 1 075 638







































































Результаты поиска

Содержание 1 075 638

Отзывы:

Похожие инструкции для 1 075 638

Бренды по названию

Популярные бренды

SICK 1 075 638, Руководство по эксплуатации

Результаты поиска

Содержание 1 075 638

Отзывы:

Похожие инструкции для 1 075 638

Бренды по названию

Популярные бренды