Главная
/
Si-tex
/
SAS-300
/
Руководство по эксплуатации

Si-tex SAS-300, Руководство по эксплуатации

Поделиться

Страница: 93 / 104

$background image$

- 86 -

Configuring your AIS transceiver

4 Configuring your AIS transceiver

Until correctly configured your AIS class B transceiver will only receive AIS messages and will not
transmit AIS messages.

4.1 Switching on your AIS transceiver for the first time

A few seconds after power is applied to the AIS transceiver, the indicators on unit will illuminate in a
pattern dependent on the configuration state of the unit. Figure 13 shows the functions of the four
indicators.

Indicator Function

Green

Unit is powered up and operating normally

Amber

Unit is in a 'transmit timeout' period

Red

Unit has experienced an error

Blue

Silent mode is activated

Figure 13 Indicator functions

If the AIS transceiver has been pre-configured the amber indicator will illuminate until a transmission
has been sent by the unit. This
may take several minutes as the transceiver must acquire a GPS position fix prior to transmitting its
first message.
If the transceiver has not been pre-configured the amber and red indicators will be illuminated until the
configuration process has been
completed.

4.2 Configuring your AIS transceiver

There are two potential ways in which your AIS transceiver can be configured:
1. Configuration in advance by your dealer or installer.
If your AIS transceiver has been configured for you by your dealer or installer you can proceed to
section 5.
2. Configuration using proAIS2
Providing it is acceptable to do so under your local legislation it is possible to configure your AIS
transceiver yourself using the proAIS2
software provided with the product.

US Customers only: It is a violation of the rules of the Federal Communications
Commission for the end user to

programme the vessel data. The vessel data must

only be programmed by a competent installer. If your AIS

transceiver has not been

pre-configured for you please refer to your dealer for advice on how to have the AIS

transceiver configured by a competent installer.

«
...
91
92
93
94
95
...
»

Содержание SAS-300









































































































Отзывы:

Нет отзывов

Похожие инструкции для SAS-300

Бренд: Latchways Страницы: 80

Бренд: Kapriol Страницы: 28

Бренд: Quincy lab Страницы: 4

Бренд: JB Systems Страницы: 12

Бренд: Calix Страницы: 9

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: Datavideo Страницы: 28

Бренд: Yamaha Страницы: 46

Бренд: TC Electronic Страницы: 67

Бренд: Tascam Страницы: 3

Бренд: Yamaha Страницы: 5

2261998USBA1-XX

Бренд: MMF POS Страницы: 5

HomeFill HF2POST6

Бренд: Invacare Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды