Shuttle HOT-597 Скачать руководство пользователя | Manualshive

Страница: 41 / 45

background image

- 40 -

PCI Latency Timer (CLK)

The number of clocks programed in the PCI Latency Timer represents the guaranteed time
slice allocated to the 82C598AT, after which it must complete the current data transfer
phase and surrender the bus as soon as its bus grant is removed.

The PCI Latency Timer is used to guarantee to the PCI agents a minimum amount of the
system resource.

The default setting is 64 PCI clocks.

MS IRQ Routing Table

This item allows the user to set BIOS IRQ Routing Table Enabled or Disabled.

PCI IRQ Actived by

This item sets the method by which the PCI bus recognize that an IRQ service is being
requested by a device. You should never change the default configuration unless advised
otherwise by your System's manufacturer.
The Choice: Level(default) and Edge.

Assign IRQ For USB

This item allows the user to assign IRQ to on-board USB controller or not.
Since on-board controller is enabled always, if none of IRQ is assigned to it, there will be a
question mark report on system device under windows 95.

Assign IRQ For VGA

This item allows the user to set VGA IRQ Routing table Enabled or Disabled.

Assign IRQ For ACPI

This item allows the user to set ACPI IRQ Routing table Enabled or Disabled.

«
...
39
40
41
42
43
...
»

Содержание HOT-597














































Отзывы:

Нет отзывов

Похожие инструкции для HOT-597

Бренд: MSI Страницы: 169

Бренд: Freescale Semiconductor Страницы: 4

Бренд: NXP Semiconductors Страницы: 12

X58 PLATINUM SLI - Motherboard - ATX

Бренд: MSI Страницы: 74

Бренд: MSI Страницы: 90

Бренд: Aeroflex Страницы: 32

Бренд: Intel Страницы: 112

Бренд: Gigabyte Страницы: 96

Бренд: Texas Instruments Страницы: 13

Бренд: Advantech Страницы: 136

Бренд: ECS Страницы: 131

Бренд: Abit Страницы: 72

Бренд: JETWAY Страницы: 48

Бренд: JETWAY Страницы: 54

NLBT-I1800 Series

Бренд: JETWAY Страницы: 51

Бренд: JETWAY Страницы: 51

Super 7 SY-5EMA+

Бренд: SOYO Страницы: 16

Бренд: protech Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды