Shuttle HOT-555 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 32

background image

HOT-555 User's Manual 31

Password Setting

This section describes the two access modes that can be set using the
options found on the Supervisor Password and User Password.

Supervisor Password and User Password

The options on the Password screen menu make it possible to restrict
access to the Setup program by enabling you to set passwords for two
different access modes: Supervisor mode and User mode.

In general, Supervisor mode has full access to the Setup options, whereas
User mode has restricted access to the options. Thus by setting separate
Supervisor and User password, a system supervisor can limit who can
change critical Setup values.

Enter Password

Type the password, up to eight characters, and press <Enter>. The
password typed now will clear any previously entered password from
CMOS memory. You will be asked to confirm the password. Type the
password again and press <Enter>. You may also press <Esc> to abort the
selection and not enter a password.

To disable password, just press <Enter> when you are prompted to enter
password. A message will confirm the password being disabled. Once the
password is disabled, the system will boot and you can enter Setup freely.

«
...
29
30
31
32
»

Содержание HOT-555

































Отзывы:

Нет отзывов

Похожие инструкции для HOT-555

Бренд: Supermicro Страницы: 2

RHINO VAP133-ACP

Бренд: Octek Страницы: 66

CLICKER 4 for STM32

Бренд: Mikroe Страницы: 16

Бренд: Supermicro Страницы: 142

Бренд: ASROCK Страницы: 2

Бренд: RIB Страницы: 12

Бренд: Intel Страницы: 36

Бренд: TYAN Страницы: 86

Бренд: Advantech Страницы: 5

Бренд: Supermicro Страницы: 109

Бренд: Gigabyte Страницы: 96

Бренд: ASROCK Страницы: 4

Бренд: ASROCK Страницы: 160

Бренд: DFI Страницы: 75

Бренд: G.B.T Страницы: 55

Бренд: SOYO Страницы: 119

Бренд: AvaLAN Страницы: 14

Бренд: Socket Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды