Shuttle HOT-555 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 32

background image

HOT-555 User's Manual 19

The user may also set those items to AUTO to auto configure hard disk
drives parameter when system power-on.

If a hard disk drive has not been installed select NONE and press <Enter>.

Drive A type/Drive B type

The category identify the types of floppy disk drive A or drive B that has
been installed in the computer.

Video

The category selects the type of adapter used for the primary system monitor
that must matches your video display card and monitor. Although secondary
monitors are supported, you do not have to select the type in Setup.

Error halt

The category determines whether the computer will stop off an error is
detected during power up.

Memory

The category is display-only which is determined by POST (Power On Self
Test) of the BIOS.

Base Memory

The POST of the BIOS will determine the amount of base (or conven-
tional) memory installed in the system. The value of the base memory is
typically 512K for systems with 512K memory installed on the
mainboard, or 640K for systems with 640K or more memory installed on
the mainboard.

Extended Memory

The BIOS determines how much extended memory is present during the
POST. This is the amount of memory located above 1MB in the CPU's
memory address map.

«
...
17
18
19
20
21
...
»

Содержание HOT-555

































Отзывы:

Нет отзывов

Похожие инструкции для HOT-555

Industrial NUC-J6412

Бренд: ASROCK Страницы: 2

Бренд: Advantech Страницы: 3

Бренд: Linear Technology Страницы: 10

Бренд: Texas Instruments Страницы: 19

Бренд: Supermicro Страницы: 124

P35D3 Platinum - Motherboard - ATX

Бренд: MSI Страницы: 104

Бренд: ASROCK Страницы: 4

Бренд: Icop Страницы: 30

Бренд: Texas Instruments Страницы: 33

Бренд: JETWAY Страницы: 54

iEi ROCKY-4782E2V

Бренд: ICP Electronics Страницы: 52

Бренд: Picor Страницы: 11

Бренд: DFI Страницы: 80

X58A-GD65 series

Бренд: MSI Страницы: 100

Бренд: TOHATSU Страницы: 130

Бренд: SOYO Страницы: 34

Бренд: Suzuki Страницы: 68

Бренд: Faytech Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды