Shur-Co 4500 HD Series Скачать руководство пользователя страница 23

Страница: 23 / 36

P/N 1121681 Rev. P

Rocker Switch - Trailer Mounting & Wiring - Standard Roll

NOTE:

Release switch at end of cycle or modified-reset

circuit breaker will trip. After breaker resets, switch will

activate motor again. To reduce unnecessary strain on tarp

components, release switch at end of each cycle.

CAUTION

Check all hardware for complete assembly before
operating. Inspect system at this time and adjust
as required.

CAUTION

Do not cut SMARTwire™.
Bind excess wire with
cable ties.

STEP 1:

Connect SMARTwire™ from electric motor to SMART

wire™ from dual-conductor socket and secure connec

tion with lock pin. Secure all wires to trailer with cable

clips and screws. If needed, use cable ties.

smartwire

™

from

motor

NOTE:

Coat each connection with dielectric grease (P/N

1704378) to prevent corrosion.

STEP 2:

Align socket over 2" hole. Using holes in flanges on

socket as guide, mark and drill two 5/16" holes.

drill

two

5/16"

holes

seven

pole

conductor

drill

hole

STEP 1:

Locate dual-pole conductor socket near seven-pole

conductor socket as shown. Determine location and

drill 2" hole through trailer skin.

STEP 3:

Fasten conductor socket to trailer with screws

washers

and nuts

smartwire

™

smartwire

™

from

dual

conductor

socket

NOTE:

Wire lengths are predetermined. Before installing

SMARTwire™ components, review and confirm wire routing

so wires reach components with ample room for connection.

WIRING SCHEMATIC

DUAL CONDUCTOR

front

trailer

secure

cable

tie

swap

wires

reverse

motor

direction

OPERATION:

Close tarp:

Push switch to

CLOSE

and hold. Observe tarp

and release switch when tarp is fully closed.

Open tarp:

Push switch to

OPEN

and hold. Observe tarp

and release switch when tarp is fully open.

STEP 2:

Check motor direction

by activating switch

OPEN.

If switch is

running system back-

wards, swap wire leads

on two outside tabs on

rocker switch.

open

Содержание 4500 HD Series





































Результаты поиска

Содержание 4500 HD Series

Отзывы:

Похожие инструкции для 4500 HD Series

Бренды по названию

Популярные бренды

Shur-Co 4500 HD Series, Руководство пользователя

Результаты поиска

Содержание 4500 HD Series

Отзывы:

Похожие инструкции для 4500 HD Series

Бренды по названию

Популярные бренды