ShoreStation SSV40108HAC Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 19

ShoreStation SSV40108HAC Скачать руководство пользователя страница 13

Midwest Industries, Inc.

Ida Grove, IA 51445

800.859.3028

www.shorestation.com

0003277

Page 14

The following are instructions for connecting the 120 volt

pump only. The 12 volt system is addressed on pages15.

Route the control pendant wire down the extension leg and over

to the pump. Connect it to the connector plug located on the pump

and identiﬁed on the drawing on page 13. Align the plugs so they

will mate. Once mated turn the outside sleeve of the connector

clockwise to lock the connection together.

Connect the wire from the micro switch located inside the winch

tube assembly to the pump by aligning the plug on the end of the

micro switch wire with the connector on the pump so they will mate.

The correct connector is identiﬁed below on the drawing. Once

mated turn the outside sleeve of the connector clockwise to lock

the connection together.

Connect the hydraulic hoses from the winch tube assembly to the

pump by mating the hydraulic connector male to female and female

to male.

Connect the electrical cord on the pump to a 120 volt power supply

line that is sufﬁcient to supply power to the pump so when it is run-

ning that there is a minimum of 109 volts.

NOTE: THE POWER SUPPLY MUST A HAVE GFI PROTECTION

AT THE SOURCE. CONTACT YOUR LOCAL ELECTRICIAN TO

MAKE SURE YOU COMPLY WITH STATE AND LOCAL WIRING

CODES.

«
...
11
12
13
14
15
...
»

Содержание SSV40108HAC




















Отзывы:

Нет отзывов